Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hi,The cisco doc says that when split horizon is enabled (which is the default), then RIP will NOT send any ad about summary addresses.What is the reason why this behavior has been established ? I really don't see what we want to avoid by not sending...
Hi,I am using Cisco Catalyst 4506 with 12.2(25)EWA4. I have Sup IV WS-X4515. I am getting issues related to TCAMLog:-000561: May 17 07:06:23: %C4K_HWACLMAN-4-ACLHWPROGERR: Input Security: Mnc - hardware TCAM limit, some packet processing will be soft...
According to number of cisco websites there there are 4 types of VTP messages :Summary-advertisementSubset-advertisementAdvertisement requestVTP join messageThere doesn't seem to be any information concerning the VTP join message or its parameters (f...
Resolved! EIGRP : CR mode
Hi,I had a doubt : When - router A sends a multicast to router X and Y, - receives an ack from X- but none from Y=> which router will enter CR mode, when the multicast flow timer expires : X or Y ?I have searched extensively on cisco.com but found no...
Hi all!i have a problem with cisco 1751v.I need to reset him to factory default (PASSWORD RECOVERY FUNCTIONALITY IS DISABLED).i read on Cisco website the solution of the break key on boot startup but doesn't work.I use different terminal emulation,bu...
Resolved! Maximum spanning tree instances
Hi,is there an IOS command to see the max. spanning tree instances on a Switch??I found the description only on the Datasheets on Cisco.com...Are the max. STP instances only Hardware related or also IOS?Thanks and regards,Thomas Feichter
Hey all, I hope this isn't a stupid question: I have a Catalyst 5500 series with WS-X5224 cards. I was just wondering if there was a way to configure the LEDs to flash with activity on the port instead of staying lit solid. Thanks!
HiI am getting the follwoing error on one our Core Switch 6509.%ACL-3-TCAMFULL:Acl engine TCAM table is full%ACL-3-RACLMAPCOMMITFAIL:Failed to map Router ACL to VLAN 10I searched it on Cisco site and found need to remove unused ACLs...But here my que...
Hi,I have read that Flow Control helps to prevent buffer issues on the receiving device by using a pause frame. However I do not know if this is a recommended best practice for Switch to Server connections or Switch to Switch connections.Cisco say th...
I am having ISP issues with my cisco 2621. It is actually my clients. And in fighting with the ISP that it is thier problem, i want to make sure I cover all my grounds. My cleints are experiencing no network access or internet access. They are a ...
I am trying to boot a WS-C3550-24 from a TFTP server but it is not working. I am using the "boot system tftp://x.x.x.x/imagename.bin" command, and I do a wr me. When I do a "show boot" it shows that it is configured for the appropriate tftp server....
how can i block specific web sites ?and how to block some specific extensions from being downloading ??????
I have a Linksys RV042 doing routing/dhcp (192.168.1.1) and a 3550 (192.168.1.4) as my switch.I recently added a second 3550 connected directly to the router (192.168.1.5). Now I've reset all settings to factory defaults on both switches, whenever I ...
I have inserted the SFP module and plug in the LC connector on both switches, but the SFP port LED does not on and cannot be enable the link up. How can I solve it?? Thanks in Advance!!Charles
Hi,I am currently using a Cisco 3750 switch. Is there any commands in to bring down the CPU load in the switch. Appreciate prompt reply. Thank youRegardsMansur
