Activity in Technology and Support
ISE - WIFI Profiling Issue
HI trying to do profiling using MAB over WIFI, i had created initial non-profile auth policy that has ACL from WLC (5508) that allows only DHCP, DNS and IP to ISE PSN, device are hitting this auth profile but keep in unknown state if i hange auth pro...
Resolved! Need Switch Stacking Help
HelloWe recently purchased 4 Cisco Catalyst 9300x 48x UPOE+ switches to use in a switch stack configuration. I have made sure that the Stack Wise cables are all connected properly but when the switches boot up only 3 switches are found and are in the...
Issue with configuring leaflist node on yangsuites
Hello, When using yangsuites to configure gnmi request with two leaflist nodes, it seems that yangsuites will create two update request for each leaflist rather than passing the two values in one update request. When I tried to run to modify the ...
Catalyst 8500-20X6C – Incorrect SNMP OID Values for Fan, Power Supply,
Hello everyone, I'm currently monitoring a Catalyst 8500-20X6C using SNMP, and I'm trying to retrieve hardware status values such as fan states, power supply status, and temperature sensors. I'm using OIDs from the CISCO-ENVMON-MIB, including: 1.3.6...
Why does c1300 mention strange locale?
I have C1300's running WhateverOSButCertainlyNotIOS v4.1.7.17 and I'm wondering why the Software information says locale is zh-CN, but also ja-JP? Are these C1300s some rebranded Chinese product?
Cisco ISE 3.1 patch 10
Installing patch 10 because of the vulnerability, but the PAN is stuck in a loop - installing patch 10, getting the error:Error: ISE Integrity Check Failed! One or more ISE program files appears to% be tampered with. Check system log for specific err...
Cisco ISE - hitting wrong NetworkDevice Group
Hello,For some reason, an authentication request for node 172.23.140.200 is hitting the wrong Network Devices Group, though there is a long prefix/32 available. Consequently, the wrong Policy-Set is chosen with Privilege Level1.Usually ISE is expecte...
Where to find the Cisco Nexus NX-API DME Model Reference?
I’m curios to work with the Cisco Nexus NX-API DME REST-API to programmatically change configuration on the Cisco Nexus 9000 Switches.However, it seems like the link to the API reference provided on the Website is broken. https://developer.cisco.com/...
CISCO MAB Auth for Wireless devices
Hi AllI want to configure MAB authentication for wireless users. The same SSID is used for 802.1X, and I would like to use MAB for specific users. Is that possible, and how can I achieve it?Thanks,
Overlapping network multicast routing
I have multiple overlapping radio man nets, which require to be in the 10.0.0.0/8. is it possible to route multicast traffic to and from each site with overlapping networks?
redirect or forwarding to mobile not working if call received external
if a call received to pilot number it will play prompt at unity connection . if the caller accept option to ring at reception it ring there and if no answer it should forward to mobile number. what happens is that it get forwarded and call get receiv...
Resolved! Downtime for certificate renewal - ISE 3.2
We have an ISE 3.2 distributed deployment (2x admin, 2x MnT, 4x PSN). We're using a multiuse certificate for Admin, EAP Authentication, RADIUS DTLS, and Portal usages. We have multiple wireless controllers that each have the four PSNs specified (9800...
allow policy & A/D user
Hello,I created a new policy to block all generative AI except a couple sites that I allow.In the policy, I allow by identities and add active directory users so they can visit the sites. One of these users tested it and was able to reach the site no...
VLAN issues
I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
Resolved! CSCwo18785-"ERROR: The transceiver doesn't support this speed"200G-DAC
Facing the below issue and it is a blocker for our product supportability with Cisco 9000 series switches.CSCwo18785 "ERROR: The transceiver doesn't support this speed" while configure 200G on QSFP-200G-DACQuestions1) What is the current status and...
| User | Helpful Count |
|---|---|
| 103 | |
| 92 | |
| 90 | |
| 77 | |
| 63 |
