Activity in Technology and Support
Migration from Anywhere Border node to External Border node
Hi there, We have standard SDA design with a fabric site including 2 border nodes with some intermediate nodes and edge nodes connected behind. The problem is we have one border node configured as anywhere and the other one as external. We plan to co...
AP going to ME mode
Hello,When I connect an AP (9162) to the switch, it fails to connect to the Wireless LAN controller(9800L); instead, it goes into ME mode and acts as its own WLC. To join WLC, I'm assigning the IP Address manually to join WLC. How to resolve this?Tha...
Help with spam Voip calls after moving to a 1100 series ISR
We have had a Cisco 867 router on our DSL line for 10 years without problem. It provides NAT to the LAN and acts as a DHCP server.We tried to replace it with a C1117-4P with an almost identical config but after doing so started receiving spam voip (...
Ceiling Microphone Pro how to access wizard when in Teams mode
Good afternoon everyone,We have recently deployed a Cisco Room Bar Pro with a Ceiling Microphone Pro. The Room Bar Pro is configured for Teams Room, but the WebEx Admin Center is indicating that the setup wizard for the Ceiling Microphone Pro has not...
Forcing 2 APs to upgrade first when migrating from a 5520 to CW9800M
Hello, I have an upgrade soon where we are upgrading from a pair to 5520s (8.10.190.0) to a pair of CW9800Ms (17.14.1). There are over 400 APs (1852s, 2702, 9115s) to be migrated. The window for this upgrade is tight. I was thinking if we could force...
Calling party transformation through SIP trunk
We need to set up a SIP trunk between CUCM (located at Site A) and Genesys (located at Site B). Both sites are connected via a site-to-site VPN. Genesys agents at Site B will initiate PSTN calls through CUCM at Site A. These calls should present a sp...
The Room Bar cannot pair the panel
I have a Cisco Room Bar running RoomOS version 11.24.2.4 c2bc63070f1 and the panel with version ce11.24.2.4.c2bc63070f1. We are trying to set it up as a Teams Room, but the panel keeps searching for available devices, even though it is already direct...
CSCwm03493 - UCCX Support for MSSQL JDBC Driver
Hello all, we worked with Cisco to get this change request added which is marked as an enhancement request. In a nutshell it is to update the available drivers in UCCX for making Datasource Connections for integrations to use a native Microsoft Driv...
catalyst 9000 - netflow - collect routing AS NOT working
HelloI am currently using FNF with C6500 router with BGP activated on it.on C6500 I can collect BGP AS info using Netflow flow record "collect routing source as 4-octet" commandWe have migrated our C6500 towards C9500; I configured FNF on itthe comma...
Cisco Secure Endpoint Not Scanning
I'm unable to get any devices to scan today in Cisco Secure EndpointChecking the device's events, no failed scan or any other errors. Multiple tenants. Something going on with AMP?
Why the AD value of StaticRoute is higher than iBGP
The R1 and R2 routers are running eBGP on the WAN side (left) and iBGP on the LAN side (right). In addition, StaticRoute for LAN is configured and advertised by BGP to the WAN side.The eBGP neighbor of R2 uses Path prepend to prioritize routes via R1...
Windows Search Problem on computers Win11 and Cisco Secure Client
We are experiencing unusual issues with computers running Windows 11 that have Cisco Secure Client 5.1.6.1307 and Secure Endpoint 8.4.5.30483 installed. The problem is that Windows Search suddenly stops working and just keeps spinning without returni...
Resolved! ISE 3.3 system certificate update
ISE 3.3 system certificate updateWe use public cert and what is recommended way to renewal cert has they are part of the deployment pri and secondary they are not part of the PAN failoverdoes it matter if i gave it two of the common name of both ISE ...
Overlapping External TEP IPs on loopbacks within a Multi-Pod
Hi guys,within my Multi-Pod (2 Pods) environment I got an overlapping IP which belongs to the external TEP-Pool from Pod 2. This fabric is not in production yet.Informations:external TEP-Pool Pod 2: 172.20.12.0/24Data Plane IP: 172.20.12.1Spine 221 I...
Terminal monitor command ACI
Hello Team,Is there an equivalent command for terminal monitor, show logging on Leaf SWs?
| User | Helpful Count |
|---|---|
| 103 | |
| 85 | |
| 68 | |
| 61 | |
| 60 |
