Activity in Technology and Support
To many interfaces on my C9300-NM-8X
I was applying the config on my C9300-NM-8X and according to the documentation all of the expansion ports should be TenGigabitEthernet. After applying the desired config the results of show run there are 4 GigabitEthernet, the 8 TenGigabitEthernet i...
New Feature: Scheduling for Internet Rules is Generally Available
Feature Overview The Scheduling for Internet Rules feature is now generally available in Cisco Secure Access. This new capability allows administrators to create and apply time-based schedules to internet access rules, providing granular control ove...
Downtime for certificate renewal - ISE 3.2
We have an ISE 3.2 distributed deployment (2x admin, 2x MnT, 4x PSN). We're using a multiuse certificate for Admin, EAP Authentication, RADIUS DTLS, and Portal usages. We have multiple wireless controllers that each have the four PSNs specified (9800...
Does Cisco ASA support FQDN based split-tunnel for Ubuntu machines?
Does Cisco ASA support FQDN based split-tunnel for Ubuntu machines? Will Dynamic split tunneling functionality work with Ubuntu?
Anyway to configure management IP for ACI switch in CLI, without APIC?
There are some spare switches with OLD ACI image (v14.1). I need to get them upgraded to v16.0 before being compatible with the APIC (v6.0.6c). I know the USB drive approach but it is kinda difficult to access the site...I do have the KVM access to t...
Catalyst Center Installation Options & Deployment Best Practices
This webinar will take your understanding of Catalyst Center to the next level with this four-session foundational series that's designed to help you Unlock the full potential of your deploymentStay updated on the latest advancementsAdopt best practi...
Additional NIC Card to BE6M-M5-K9
Looking to add an additional NIC Card to the UCS BE6M-M5-K9 server. Has anyone done this that can provide some guidance.
CErtificate guest ISE
My customer neeed s to upgrate expaire certificate guest portal .I n my head allwys has the same create rthe CSR and after of taht bind the certificate . I always made this way for what if you fgenerete the csr from ise the key is inide and ypu pas ...
Resolved! Upgrading firewalls from ASA 5555-X to FPR-1140, AnyConnect client upg
ASA5555-X is going EOL this fall, so we have to upgrade. Looking at running FPR-1140 with ASA to maintain easy migration of 70+ VPN tunnels. Also using AnyConnect 4.9 client currently. I haven't found anything saying i wouldn't continue to be able to...
Looking for Help or a Guide for Writing Basic Config File
Good Afternoon All,Looking for kind of a step by step guide. My org recently purchased 3 9300L switches. Two of them are 24p's and the other is a 48p. I am assuming I can write one file then make small tweaks due to the port capacity. These switches ...
Cisco IP Phone 7960 Series
Hello,I was told by Cisco Support that they no longer support the 7960 Series. Our phone system in our office is down and I need support. We already had our phone service provide out and they determined it is not an issue with phone service, rather o...
WLC-9800 - AP C9136I-ROW - Slot 2 cannot be enabled
Hi,I have C9136I-ROW joined to the 9800 controller os 17.12.5.It is working fine inSlot 0 : 2.4Slot 1 : 5GHzSlot 3 : 6 GHzI can disable/enable all these three but the problem is for slot 2 that is disabled by default and I cannot enable it, I tried t...
UCSM 4.2 (3j) backup failure on the remote host
We have UCSM 4.2(3j), and backups are failing to a remote Linux box.We have the following error codes in the UCSM
VLAN issues
I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
How do I connect to NSO WebUI with a static IP?
Run the nso 6.5 local-install, ncs-setup --dest ncs-run commands The default ncs.conf is set as follows: I set a static IP to access the webui on the same network band. When I access the webui with a fixed IP, 400 Bad Request occurs. Even if y...
| User | Helpful Count |
|---|---|
| 90 | |
| 79 | |
| 73 | |
| 68 | |
| 65 |
