Technology and Support

ISE profiling an IP range

HiI have a requirement to profile devices based on IP range.  This is easy if my subnets are on octet boundries.  So I can match the 10.10.10.0/24 subnet with startswith 10.10.10 and that works fine.However if my subnet is, for example, 10.10.0.0/20 ...

CUCM | 15 SU2 | SRTP | Phone registraiton error

Dear Cisco community, We are migrating the server to mixed mode and have created the secure phone profile to register the phone. However, the phone is not getting registered, and CM logs are showing as below; all the self-signed certificates are vali...

Resetting a Cisco Air Cap 1552E access point to factory defaults!

I am trying to reset a Cisco Air Cap 1552 E access point back to it's factory defaults.  I have tried every mode button press and release from what I read online, but nothing is working.  I do not have an option to reset it via a controller.  Can som...

Running 10G access switches with CAT5E infrastructure

I've had mgig/10g 9300 switches running for years in buildings with CAT5E infrastructure. It's not been an issue because pretty much every device had only a 1g nic. Really, I can't think of a single device that actually took advantage of the mgig/10g...

550 5.1.0 sender rejected

I am a simple User of email through Shaw.ca. My friend is a User of gmail. He sent an email to multiple recipients (a bulk email?). All of the recipients with Shaw.ca email address caused this rejection message to be sent back to my friend, the sende...

Generate In band engaged tone signalling with IOS Voice Gateway

Hi All, I need to replicate In band Engaged tone is a lab environment. My current set up is; CME <Q931 Trunk> IOS VGW <H323 Trunk> CUCM. What commands would I need to configure on the Gateway so it responds with in band engaged tone when dialling fro...

ASDM error certificate present in this device is not valid

hi@jhnet On ASDM i'm getting an error message "The certificate present in this device is not valid. Certificate date is Expired or not valid as per current date" only on secondary device, Primary is working fine. Any suggestion how to fix this. check...

ISE posture issues

DearsWe have DNA Fabric environment with Cisco 9800 WLC and ISE 3.2 integrated with it, endpoints Windows and MAC OS are using Anyconnect Client posture module (version 5.1.10.233) , on our network we have Quarantine subnet and Production subnets for...

Is ISE 3.4 stable for production?

Hi,We're currently at ISE 3.1 patch 10. We intend to upgrade to ISE 3.4 patch 3 which is marked as suggested version now in Cisco's download portal. Since we've had many problems even with suggested software versions, I don't value a star in a Cisco ...

FMC 7.4.2.3 - Intrusion policy - Snort3 version page access issue

Hello everyone,We recently upgraded from 7.4.2.1 to 7.4.2.3 patch.Since the upgrade, I cannot access the snort3 version Intrusion Policies.In the Policies -> Intrusion Policies -> in this list, at the end of each item, there is a button "Snort 3 Vers...

Users unable to connect with an AP SSID WLC9800L install on VM

Hi Team,I have an WLC9800L install on VM..My AP 3802 is discovered into it and also SSID is broadcast but my end user is unable to connect with this SSID.Note: All devices like WLC9800L install on vm and AP in same vlan..and use will also get the IP ...

Custom labs on CML not working

The devices in custom CML labs are not reachable from outside via VPN but the default lab works fine ...Please help me sort this issue out . Thanks 

pyATS runtime.synchro.dict not updating nested list during Easypy run

Hi all,I am working on a pyATS/Easypy test automation project where I maintain a shared dictionary across multiple test cases using runtime.synchro.dict.Here is my setup:# Initialize shared dictionary in main scriptshared_dict = runtime.synchro.dict(...

redistribute ospf to static route and learned internal subnets