TelePresence and Video Infrastructure

I have been beating my head to a bloody pulp trying to get this to work. Hopefully someone here has an answer. I have a 3540 Gw2P I am trying to setup (SW 5.0.22). I can make Ip->ISDN 384Kbs calls all day long. However I cannot connect ISDN->IP at g...

hi alli'm trying to understand if its possible to register a sip video endpoint (polycom vsx) to ccm 5.0.it seems like ccm5 is not a sip registrar and one needs to use cisco sip proxy for that but i might be wrong.anyone here managed to register a si...

Hi!I have several IP-phones and IP-communicators with cameras (VT advantage). Everything works fine except one communicator.On this PC during "video check" and conversation picture on "remote" window is separated into four parts with the same oblong ...

I downloaded a new version off ip/vc 3511 software (v4.0.31) and ip/vc 3511 emp (v.3.0.5). When I upgraded the version v4.0.31 was ok, but when I upgraded the version v3.0.5 for emp, I received the following message error:Upgrade process failed : Th...

Hi EveryoneI'm very new to all of this please bare with me. I have been tasked to come up with a backup plan for our Callmanager 4.0. The BARS utility looks like what I need, however I am not able to find it in order to download. Can anyone help?Than...

Hi there, I've implemented a couple of 7920 wireless phones. I have configured the 1310 APs with QoS and the phones connect up to CCM fine. The entire local network is QoS enabled. My problem is that i periodically get 'clicking sounds' when i make...

problem with gateway q.931 signaling to centrex call can not complete (gateway instructed by gatekeeper), require centrex route call to next least cost route.

We're running CME and after adding "video" to the ephone and reseting the phone there is no camera icon showing up. Is there anything else we need to add to the config to start video? I even restarted the router with no success.2811CallManager Expr...

I am testing video between an H.323 Polycom Viewstation (version 7.4.5) and Call Manager 4.1.3 SR2. On the Call Manager side, the clients could be an IP Phone for a audio-only connection or with a CVTA for a video conference. I can call from the CVTA...

I have installed VTA 2.0 in a machine with IPC 2.0.The VTA recognizes the camera but not the IPC.What?s is the problem?Do I need to do something?Thanks

Is there a command that can open & close a dialpeer on a specified time on a router

I am suresh, I am having the IPTV3441 BCAST server with the IPTV server version 3.5 and content manger 3.5. I like to know about viewer , is it necessary to me have iptv Viewer. How can my users view the broadcast. Do i have to install a software. ...

I've noticed that when creating CTI ports through IPCCX 4.0(3), leading zeros are ignored. For example, CTI ports 00001XXX are created as 1XXX. Is there a workaround?

I am running inboung faxing on a 2821XM router, 256MB, 12.3(11)T8 using the on-ramp/off-ramp TCL's 2.0.0.0 (outbound is configured, but not used), with 2xe1's (primarily used for voice). Incoming is working fine for the majority of messages (about 5 ...

Hello,I'm looking for documentation that explains what everything listed here means:*Mar 2 05:54:43.996: htsp_process_event: [1/0/0, 1.4 , 34] em_onhook_offhookhtsp_setup_ind*Mar 2 05:54:44.000: htsp_process_event: [1/0/0, 1.7 , 8]*Mar 2 05:54:44....