TelePresence and Video Infrastructure

Resolved! SX20 resume issue

Hi all,SX20 does not display video after resuming a call with Polycom Real Presence Desktop(RPD) for Windows.Is this a known issue?1. Dial IP address of RPD from SX20 on H323.2. Press HOLD button on SX20(using Cisco Touch).3. Press RESUME button on S...

Resolved! TMS 13.2.2 - SQL 2005 to SQL 2008 migration

I want to confirm (as there are already some posts about it) that migration from SQL2005 to SQL2008 db does not require any reinstalls / actions on the application side.We have TMS 13.2.2 running with remote DB on SQL2005. Our DB team is migrating al...

Question about EX90 PC port speed/duplex

Does anybody know if the EX90's PC port speed/duplex settings follow the settings for the primary port, or does it always stay at Auto?Is there a way to manually set it?As we utilise fibre in many locations, hard setting speed and duplex settings is ...

Resolved! Cisco MCU 5320 and Polycom vsx

Hi!i have problem with these devices. Content doesn't work correctly. MCU push content to same h.261 protocol with video to vsx endpoint. So quality of content are very poor. Is this interoperative problem or sofware problem? any other endpoint it w...

TMS & SNMP Server connection

Hi Folks,My customer is trying to link their TMS server to their SNMP server and I showed them what settings in TMS need to be adjusted but they are looking for a tms.mib file, does anyone know where I can get it? In past discussions, I've seen that...

Routing incoming calls from outside

Hello everyone. I am new at Cisco VOIP and i need some help. I manage to create VoIP on my router C2911 and i have 3 IP phones. I have one voice port that is conected to my country telekom(ground line whose number iz YYYYYY). My phones have 3 digits ...

Findme using B2BUA is not working

Hi,I am trying to configure Findme account for Lync 2010. The B2BUA link to the Lync 2010 server is active and calls were successfully made between Lync clients and VCS clients. However, Findme account was never registered to Lync 2010 server. The...

Resolved! Encryption setting on SX20

Hi all,As mentioned in "sx20_quickset_administrator_guide_tc60.pdf" page 55, SX20 can use AES-128 if "Encryption Mode" is set as "Best Effort" and a farend endpoint/MCU can also use AES-128.But if the farend endpoint is not able to use AES-128, does ...

thoughts on c20 setup behind firewall

Hi I have a setup where there are 2 c20 setup on a internal company network. Origginally they used the system for meetings internaly but now they want the unit in there main office to have connection to the outside world as well.Easy enough get a pub...

TCS Playback Error

Hi,I'm encountering problem on playback of recorded video on the TCS.I already installed all required players and test to play the video but i'm still encoutering problem.Please see screenshots on the error during playback.For Flash:For Silverlight:F...

Replacement Camera for an old MXP6000

Good Day,I have a client who has a Tandberg MXP6000, and the camera was damaged and needs to be replaced.The original replacement camera is now end of life. Is there a camera Cisco offers that will work with this model? If so how can someone point ...

Resolved! Need recommendation for 70" - 80" monitors for C-series

I'm getting ready to install a C90 system with large monitors. I'd like to go with 80" LCD TVs rather than professional monitors. My main reason being is that the current 80" monitors on the market are really deep/bulky and are much more expensive (...

Resolved! Wall construction is not the option is RRA offline form for TX9200

I am working for the offline TX9200 RRA form. The wall construction is " Triple layer of 5/8 gypsum board on metal studs/ with insulation" but it is not on pull down manual, so can only select the option as "Other". Is it any issue for the online RRA...

Resolved! SX20 calling SIP

Hi I would like to know, is it possible to call from SX20 to other endpoint with adress (100000@xxx.xxx.xxx.xxx) without register to VCSMeaning call as a standalone device to other endpoint.If so, could you guide me.Best RegardsSyahrir Mohamed Yatim

VCS-E Registration, Endpoint unresponsive

Dear AllI have the follow Situation:- some EX90 and some Profile52(C-40 Codec) - registered on VCS-Expressway with SIP and with H323- Authenticated on the VCS-E via Local DatabaseBoth System are "managed" via "Behind Firewall" and both system have ac...

TelePresence and Video Infrastructure

Forum Posts

Resolved! SX20 resume issue

Resolved! TMS 13.2.2 - SQL 2005 to SQL 2008 migration

Question about EX90 PC port speed/duplex

Resolved! Cisco MCU 5320 and Polycom vsx

TMS & SNMP Server connection

Routing incoming calls from outside

Findme using B2BUA is not working

Resolved! Encryption setting on SX20

thoughts on c20 setup behind firewall

TCS Playback Error

Replacement Camera for an old MXP6000

Resolved! Need recommendation for 70" - 80" monitors for C-series

Resolved! Wall construction is not the option is RRA offline form for TX9200

Resolved! SX20 calling SIP

VCS-E Registration, Endpoint unresponsive

3rd Party Interface not receiving incoming call notification

How to make generic Test Call using a Cisco Codec Pro

CISCO ROOM KIT EQ and USB Serial Adapter

Capture customer survey feedback using HttpFeedback

Connecting Multiple PTZ4K Cameras to Codec EQ

CSCCSCwo61235 - No Mic input from integration with Shure ANIUSB-MATRIX

How to connected New Cisco Ceiling Microphone Pro with Room Kit pro

Converting Codec Pro to MTR – Network and Room Navigator Setup

Codec Pro RoomOS 11.5 to 11.20

Webex Room Kit Pro and Cisco P40 or 12X cameras