Hi all, I'm trying to get UCS gear warranty information in programmatic way python/curl for automation project.Could you help me how to start off. thanks
Hi all, I'm trying to get UCS gear warranty information in programmatic way python/curl for automation project.Could you help me how to start off. thanks
Dear Team,After the failover of FI-A to FI-B when we check show cluster status its show FI-B as primary and FI-A as subordinateNow the FI-A is Back on line and HA shows as ready, but when we check show cluster status its still shows FI-B as prim...
I have a brand new ISR4431 with UCS E EN140N module. I got the access to CIMC over network and status shows ok. But when I tried to launch KVM from CIMC, I got "network connection has been dropped."... I did try to factory reset the module, but no ...
Hello ! I upgrade ucs manager to version 3.2(3a), but my servers b200m2 with m81kr adapters don't support this firmware and write faults "hardware mismatch". Now i want downgrade to 2.2(8j) version, but when i try make it i got message - "one or more...
Hi Cisco Community, I have installed 4x new B200 M5 Blades on UCS-Mini chassis. After a power outage, all B200 M5 system clock is setted 1/1/2010. Where is the RTC battery in B200 M5? Thank you and cheers!
Long time lurker, first time poster! So I picked up a 2nd had C220 M3 for use in my home lab. I am running into issues that I hope people can help with, so thanks in advance! Things I notice:: So here is the deal. The server takes anywhere f...
Hi, maybe some has any suggestion for my FlexFlash RAID challange... the Problem: - FlexFlash RAID Degraded with to health SD Cards what i have done: - reset / Activate Flexflash Controller - reset partition default - Sync Card Config -> No change ...
Hello, I am using B220M3 blade servers im UCS Manager 4.0(1b) without problems. Yesterday, I wanted to add a C220M3 rack server. So I directly connected the VIC 1225 to my two FI6248 (Fabric A and Fabric B). VIC 1225 is in slot 1. I also resetted the...
Hello, I am attempting to install Windows 2016 on B200M3's. On two of the blades I was able to do this successfully after setting the UCS Boot Policy from legacy to Uefi. After I did this I was able to install the OS, however after the OS was loa...
Hi, Has anyone created a SNMP GET rule in their favorite monitoring system for Cisco UCS Manager to look for Faults? Specifically Critical and Major fault events? Regards, Orjan
With Cisco WAAS Appliances (WAE/WAVE) when the TCP connection limit of the device is reached, all new connections will be passed-thru without being optimized. What is the behaviour with ISR-WAAS and vWAAS(on UCS-modules) when the TCP connection lim...
Hello All, Can anyone help me out with ESXi boot from SAN. Currently we have all the ESXi servers boot from local disk and we want it to boot from SAN. we are using 3PAR SAN and need some help/instructions for creating boot policy in order to set up ...
I'm trying to install Linux on a new C220 M5 with the Cisco/Avago 12G HW Raid controller. I'm trying with just a single drive in Raid-0 config with a virtual drive configured and set as the boot drive. When I boot into the install Linux identifies...
I have cloned an existing profile and attached to a B200M3 blade in UCS 5108 chassis. The initiators seems to register fine on SAN. However, unable to see boot LUN's configured. * There are no local drives * First boot order is SAN and Second is cd-r...
I have forgot to bind to a HBA Template while did the customer activation. Can we bind a vHBA Template while blade is in production ? Does this cause a Host Reboot or any issue for SAN traffic to customer ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 05:23 PM | ||
04-16-2024 02:26 AM | ||
04-04-2024 11:22 AM | ||
03-18-2024 06:52 AM | ||
02-27-2024 07:34 AM |