Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, need help to understand what my problem is? Airplay situation is as follows:Wireless to wireless devices - working fineWireless to wired devices - working fineWired to wired devices - working fineWired to wirelss - NOT workingAny advise on what s...
When connecting to the wireless network I have noticed that the clients will often skip an AP 10 feet away and connect to one two floors up and 100+ feet away. That doesn't sound very efficient and data rates are pretty poor.Can this be fixed?My test...
I would like to get some clarification regarding the user idle timeout WLAN configuration checkbox. I read on here that if you don't configure a idle time-out value within the WLAN the global system parameter will be used instead (which is 300 secon...
I am running cisco prime version 2.2.How can i add Lightweight AP?I see that switches and WLAN controllers are added, but the AP's /Radio is not showing up. But when i punch in the ip address of an AP, prime finds it but says device Unknown.Please se...
Dear all i have cisco Wlc in that i create 3 sis id.i i want to give only internet access to one SSID which Can not access internal service. can any one please tell how to do block and next is to hidden SSID with protection. regards.
anyone deployed 9800-CL on VMWARE environment ??I am able to deploy 9800-CL with SSO on single UCS chassis.Dont know how to setup UCS chassis for SSO of 9800-CL
Hi,I have a WS-C3850-24P wireless controller that manages three AIR-CAP1602I-T-K9 access points.The software version of the controller is 03.06.08.E RELEASE SOFTWARE (fc1), IOS cat3k_caa-universalk9.SPA.03.06.08.E.152-2.E8.bin.The APs are connected d...
Hi, allI got one interesting issue with wireless 5508 controller. we have ordered two WLCs, one is air5508-12-k9, Anther one is air5508-HA-k9.Now, we are going to form HA mode and HA box will become standby mode. One issue we are seeing now. after co...
Hi, We have a remote site with FlexConnect and mainly Win7 devices. Last week we came across IP-adress conflicts for that scope. The Clients use the same Subnet for both NICs and they are active at the same time. As I could not find reliable informat...
Hi all,New to Meraki and have recently purchased MX65 and MR55. MX65 working fine as other services connected directly/indirectly are working fine.Configured Port 11 (PoE+) to be a trunk using Native VLAN 1 and VLAN 347DHCP configured for VLAN 347Con...
Why is the AP1541 Authenticator sending an incorrect Access-request packet towards the Radius server? It seems the server doesn't know how to respond. But if I do a "test aaa radius from the WLC - the server response. please see attachment /Q
Hello i have a 2802E mounted on a wall. What direction should the AP be mounted at? port side facing up? Or port side (poe etc) facing down? also for antenna should all antenna be facing up or two up and two down? I am not sure how the best pract...
Hi,We are having to migrate all our APs from one vWLC to another vWLC (due to various issues including migrating from VMWare to Hyper-V). I'm using 1 AP as a test before moving the rest.I've had various issues in doing this, so will describe where I...
Hello guys. I need your help. I have the following machines: WLC 8.2.166.0 vMSE 8.0.150.0 CPI 3.1.0 I can see reachable the MSE from CPI, but the NMSP status is inactive. all machines has the same time zone and clock. Thank you for your help
Hi Everyone,Time and time again, Meraki support has told me that the recommended SSID is no more than 3. I've stepped into a multi-network environment that has a minimum of 8-10 ssids broadcasting. Im in the process of trying to plan some consolidati...
