Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Hi all I've got a new WLC 3504 with 8.5.110.0 which I just installed. What I haven't managed though, how can I, if it is even possible, assign a VLAN to one of it's physical ports? I have connected the port 5 to a Switch with a trunk and my idea is n...
2504 FW 8.2.151.0 with 6*3502 APs, 802.11n clients. Network Summary, Clients screen shows Usage and Throughput stats. What is the significance of these figures? What would be good ranges for both?
Currently my users can't access public wifi because they are re-directed to the proxy before they can get to the public wifi landing page/terms & conditions etc. I need to allow them to log on to public wifi but then route them to the proxy after tha...
hi everyone i have WLC 2504 with 15 AP 1142 , firstly how i can control a broadcast of 2.4 or 5 ? and my question here if i want to transmit 5ghz (because it better than 2.4 in rate) but its cover small space than 2.4 so i want to put 5 ghz as primar...
hi guys we access point AP AIR-CAP 1532E-E_K9 it got an IP and sending a request to controller but it doesn't joined the controller we tried to add the MAC to the MAC filter also it is in one country we did a hard reset but we weren't succeed could...
I have a 2802 serving as a Mobility Express controller, with 2 2702's attached. Using version 8.5.103 of the firmware, I'm having serious issues on the 5 GHz band of my SSID's with Mac OSX clients (constant disconnects, yet client shows connected to...
Hi, Community! I've met an issue with security requirements needs to be applied on wireless infrastructure built on Cisco WLC 2504 and ISE (radius, CWA, authorization policy). The issue is how to force users, authorized by CWA and registered their de...
Hello everyone, I have been trying to find an answer but no success so please forgive me if that has been covered in other thread. I currently have vWLC (8.5.105.0) + 2702I setup at home/lab and have been using that with no major issues. The set...
Hi all , is it possible we have two mobility controller on the same network ? because i have installed one of the mobility controller and when i am trying to install the second mobility and it will keep sending request to join the first mobility c...
need to ask if my pc has been hacked or virused becuase after my pc connected to network the pc consumed hug bandwidth and i didnt donwload any thing or open even browser i check the netflow on the gateway interface also checked the output on gatewa...
We purchase multiple 5 AP adder licenses for 2504 WLAN controller, registered all PAKs and get the license files for each adder license. To install/activate the license into 2504 WLAN controller, do I need to install the license file one by one in ...
Hello, I have a question for you to solve controller's problem. I have just arrived in my company and I owe parameter a controller to understand the functioning and the credit note one of the change, because the former IT specialist has me to leave ...
Hello, I'd like to ask few questions and appreciate guidance to help me in my solution design. we have 11 nearby classes (as in the attached .jpg), we have four Cisco 1852e AP in hallway, each class wall is solid concert with wooden door, 25 stude...
I have a registered AP2802 and connected to a 3850 switch. The AP admin status is enabled but the Oper state is down. Th power level is showing 5(*) , clean air operation status is down. Can you help in bringing up the AP? . The switch is not PoE, s...
Hi All, Does 5760 support ISE posturing, I haven't seen any document regarding this nor any discussion in the support forum The ISE compatibility matrix says it is supported, has any one worked on posturing with 5760 Regards Nikhil
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-09-2025 06:25 PM | ||
| 12-08-2025 01:34 PM | ||
| 12-07-2025 01:43 PM | ||
| 11-13-2025 02:28 AM | ||
| 09-02-2025 03:53 PM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 2 | |
| 2 | |
| 2 |