Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have a 5508 running 8.2.166.0 and that I cannot access remotely. I can access the CLI via the console port. Is there a command I can run to try to regain remote access without rebooting the controller?
Not sure if this is possible but we are currently running 5 WAP371's in cluster setup mode, using 802.1x and a Microsoft NPS/Radius server the laptops currently connect fine to a single VLAN. we are now trying to segment the users and use Dynamic...
I am exporting maps from Prime to import into CMX. When I do the Prime export, I do not see the maps on my computer in the downloads directory as I would expect. Any idea where else they could be downloading? PI 3.3 and CMX 10.4
I have a 2 member interface group associated to a WLAN, interface 1 and interface 2. I know the controller round-robins clients between the interfaces in the group when they connect to the WLAN. If the controller assigns a client to interface 1 and...
PCI Light is illuminated w/ code 26 being displayed. I've looked and looked but can't find what the hec it is.Any ideas out there anyone?thanks, robFigure 1-5 Light Path Diagnostics Panel Components
Resolved! Content Filtering/whitelisting
Have a bunch of MR 42 along with MX100 and MS switches. About 5 SSIDS, one of them needs to have all internet blocked with the exception of a few specific sites. Didn't see a way to do that with the Layer 7 rules. Can this be done? (each SSID is sep ...
Hi! I have a Cisco C1111-8PW router, which has a built-in WLC and a built-in Wireless AP. Currently, they are configured for FlexConnect, but I am having some issues setting up some VLANs on the WLC and the APs and using the VLANs, so I figured i...
Dear all I am trying to install my new WAP361. I am not an expert and I am facing a few issues. I managed to launch the set up wizard from my MacBook Air but it has been running now for 2days with a message saying 'This may take a few moments'.This i...
Since we migrated our entire infrastructure in our Warehouse environment we have had performance \ connectivity issues Migrated from local 5508 WLC to offsite 5520 Migrated from 1242 APs to 2802e APs with Omni directional antennas (AIR-ANT2544V4M-R...
Hi, I am currently trying to troubleshoot why a 3802i is staying in a low powered mode even with a 802.3at PoE injector attached. It is a deployment of around 12 APs with 6 of them remaining in that state. Logs on the APs show CDP PSE negotiation tim...
Hi I'm having problems with Sip Trunk Between CUCM and Asterisk, in the route pattern i have defined a route for numbers 86XXX in the Asterisk Side they can dial to CUCM Users with no problems, and when a registered Phone on CUCM try to dial an Aster...
Hi all, I have few 1310 LWAPP access points.I don't have any WLC and I want to convert it to autonomous AP. Please advise me how to convert 1310 AP to autonomous AP if anyone knows. Thanks Sudeesh
Resolved! wireless validation survey
Hello.I've been hired to perform a report of a wireless site survey, and I'm wondering if it should include the credentials for access points and cisco controller.I couldn't find this information online.I've another concern about the power settings ...
Hi I am having some problems with installing a star-certificate for WebAuth on a WLC 3504. I have configured the WLC for local webauth and clients will get the webauth page, but gets a SSL error. I have configured the virtual interface to using a...
Hello, i have an CAP 2602 with IOS Version ap3g2-k9w7-xx.153-3.JF9 I have access to the GUI but i can not activate the Radios. When I try it at Easy Setup -> Network Setup - i got a failure. See--- Thats the default: Building configuration... Cur...
