Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi.. i have running cisco vWLC controller in my location A, its working perfectly here. Now i have another location B where i have APs registered with controller in location A. I have created another WLAN and set location B dhcp server assign locatio...
Resolved! web gui error 3850 wireless
hello guys,I have a problem with a cisco 3850 and need ideas to try to overcome it.we have updated the 3850 version to 7.3.00.with the site admin user privilege 15 I can access the wired page ... but if I try to access the wireless part with the same...
Hey guys, I have this problem: When a user logs in using Layer 3 on an Access Point, the user goes away for a few minutes, when the user comes back the AP asks to login again. I tried enabling Sleeping Clients on Layer and gave them a day, but it's s...
I have two brand new aironet 1702I-A lightweight access points that I am trying to join to a new WLC 2504 running 8.0.100.0, I can see the discovery request come in but shortly after the following entry is logged by debug capwap on the controller:*sp...
Hi guys, we are working with MSE from some time and few days ago an interesting issue appeared.Do you know what is the correlation between floorNumber and floorRefId?As we receive info about the maps from MSE API, it returns the value of the floor 'f...
Hello,to create a GSM profile, we need a "username", "password" and un "APN" provided by the Service Prodiver, if you have more than one router Cisco 819, should we have a "usernale" and "password" for eatch router, or the same "username" and "pass...
Is it possible to do the following on a 5508 WLCI have a management and one other VLAN trunked to a switch, say 10 and 20 I have an interface configured on the controller as VLAN 10 with an IP address of 192.168.1.1/24 I have a management interface o...
One WLC is serving multiple sites with different QoS requirements. So we have multiple WLAN profiles with the same SSID, L2 policy open. All of them are anchored at the same anchor WLC. There are the same WLAN profiles with the same IDs at the anchor...
Resolved! Band select
Hi !What type of band does you can recommend to use? Only 2.4 ? or only 5.0?I know that 5.0 its more faster than 2.4 but, what happens with modern devices thats only has 802.11n?, they will connect to the WiFi or may present problems?We use an WLC 44...
HelloIt is possible to configure SNMP in an AP lightweight with WLC 5508 to get some information with snmpwalk as a AP Serial number? Thanks for your help Regards
Dears,We have a wireless infrastructure here using a WLC5508, and APs 2602i, 2602e and 3702e.Some users complain about signal strength as per below...Sometimes they really get a low signal... 2 or 3 bars..... When I saw at Controller,even when they a...
I am trying to find information on whether it is possible to setup bridging between two lightweight AIR-CAP1532E-A-K9 units and NOT have the traffic be sent back to the WLC via capwap tunnel. My goal if possible is to keep the traffic local to the A...
Hey all, I have a project coming up where we were going to replace some aging 4402 WLCs with 5508s running newer, 7.4.121.0 code (possibly even newer). Due to costs we were considering leaving the 1252s in place until we decided on 3602i/3702i, but 1...
Resolved! Upgrade FUS and WLC software
I would like to download the FUS software, delay the reboot, and then download the WLC software and then do the reboot. Is this a ok practice or is it a no no?Note: My controllers are also setup in a High Availability group.
Hi Everybody I look after over 40 5508s WLC and we have upgraded a few of them to 8.0.110. We have had 2 in the last week die. when I say die I mean we loose everything the units no longer even respond on the console port. Both of the controllers ...
