Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.if possible please send me step by step instruction, any help is gladly appreciated.thank you in advance,...
Hi,Just have a minor confusion today, what is the major difference when we have APs connected to the Access port of the Switch of when we have Trunk port connected to AP. Well, I understand the difference between Access port and trunk but on trunk we...
Hi ,Can we use AIR-AP1142N-A-K9 for India Domain ? , as per the compliances it is –N . What is the technical difference between AIR-AP1142N-A-K9 and AIR-AP1142N-N-K9, both the AP configuration guides are same will it work or not ? Regards
Hello All, I have 10 Ap´s in a building under a WLC5508 with CleanAir activated, however when the users, turn on a MW oven, the clients located near, lost completely their connections.I have activated the EDRRM, but the interference is in all channel...
Hey guys...I'm new posting here, but I've been reading you for a long time... And I need your help now...I've setup an Aironet 1260 to authenticate users through a Radius Server (IAS 2003). I configured the Remote Policies just to allow the Domain Us...
This original post is edited to correct some factual errors, but the error remains and I still need help with my quaestion at the end!! =======Hello!I have (and my customer) a rather "cute" problem ... Two months ago I installed a WLC5508 with sw r7...
Hi,I'm having some problems configuring a 2504 wlc and a couple of APs (1131) connected to a HP ProCurve switch. I would appreciate any input as I do not have any experience with HP ProCurve switches.The WLC port1 are connected to HP switch with vlan...
when i reset the device it is open in by default ip in GUI but when i configure the device after that when i enter save and reboot command it is not open with new ip in gui.
Resolved! WLC 2504, directly connected APs
I need to configure a 2504 wlc and two 1142 APs that I want to connect directly to the wlc. I've heard I can't use the PoE on port 3 and 4. If so, can I use power injectors instead? I can't seem to get the APs to speak to the wlc. Using example below...
I work on a college campus that has thousands of students a day accessing our wireless network. We have broadcast SSID that the students use to connect to the internet. The students usually have more than one WiFi enable device on them and their la...
Hi,Could anyone please advise if there is any difference in the power supplied to a 1142N AP when using a power injector (AIR-PWRINJ3/AIR-PWRINJ4) compared to using poe on the switch port (2960S 24 port POE switch WS-C2960S-24PS-L).Thanks.
Hi Team,I wanted to know WLC 5508 - Back Plane Speed with AES-CCM Encryption.Can anyone guide me to get this details?RegardsJana
After going to the High Availability Tab in the WLC GUI and setting the primary, secondary, and tertiary, how do you see that in the CLI in the AP?I tried using show capwap ip config, it doesn't show any entries at all?And also, is there a command to...
Hello,can anyone tell me the OID for the count of the APs connected (and Status UP) to a WLC 5508?Thank you...
The problem is we have a WLC version 4.0 and have multiple SSIDs, but one has been created with WEP security is specific to the directors of the company. The scenario is that mobile devices (Blackberry, Iphone 4, IPad 2, etc) have connectivity proble...
