Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi:I bought Cisco AIR-WLC4402-12-K9 with 2 x sfp transceivers 3CSFP93-4500And WS-C3560-24PS-SMy Question is which module or modules will i need to connect them up.Regards,Nabil

CSCO11177557 by Community Member
  • 1160 Views
  • 4 replies
  • 0 Helpful votes

we are running WLC version 5.2.193.0 with 20 APs. But one cannot registering to the controllerdebug on the wlc*Jul 19 14:51:38.866: Failed to process CAPWAP packet from 10.29.32.35:7173*Jul 19 14:51:41.866: 00:12:01:c5:c0:c4 AP not registering with B...

Hello !I'm on WLC 5508 . It doesn't matter if passive client feature is turned on or turned off , when you try to increase "User Idle Timeout" you can see this message:In our network, a lot of clients gets deauthenticated. I thought it would be usefu...

EvaldasOu by Level 8
  • 12286 Views
  • 15 replies
  • 0 Helpful votes

My wireless network consists mainly of approximately 1400 AP's 900 x 3602's, 500 x 3502'sThe majority of these AP's especially the new ones have been manually optimised for channel and power settings. We paid an external surveyor to survey and optimi...

Sam Takach by Community Member
  • 2008 Views
  • 5 replies
  • 0 Helpful votes

I have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I...

Hello, I bought for mistake 4  AIR-LAP1262N-E-K9.this is not an autonomous access point insted I needed a AIR-AP1262N-E-K9mi question is can the  AIR-LAP1262N-E-K9 work in autonomous mode ? is it possible to install te IOS version of AIR-AP1262N-E-K9...

Hi Guys,My Company has just purchased a vWLC together with AP Models 1041 and 3600.We are intending to deploy a "local" Wireless network (no cloud) and I saw the limitations listed.The most disturbing issue for me is not having the ability to use the...

jonathan by Community Member
  • 4281 Views
  • 2 replies
  • 0 Helpful votes

Does anyone know the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is. Anyone know?Sent from Cisco Technical Support i...

Cisco1619 by Level 3
  • 723 Views
  • 1 replies
  • 0 Helpful votes

Hi good day sorry.I'm new to this, but it's a start.I have a question for you. I am working as a network administrator IP phone, the company made ​​a firmware upgrade to CUCM version 8.5, the following versions was that wireless phones CP 7921-G are ...

Adrian Leon by Community Member
  • 4361 Views
  • 15 replies
  • 0 Helpful votes

I have this situation where we need to explort WCS data to Prime infrastructure 1.2 (or 1.3)The problem is that the Prime 1.2 is already setup for the nework and WAN.Is it possible to migrate the WCS data on top of a existing database on a Prime serv...

My questions is in relation to disaster recovery, for wireless.  We have our main data center, in the US, with two 5508 controllers.  We have a DR location, in Europe, with two 5508 controller.  We're upgrading our 5508's to the 7.4 code, so that we ...

Dan Man by Level 3
  • 2685 Views
  • 4 replies
  • 0 Helpful votes
Top Solution Authors
Review Cisco Networking for a $25 gift card