Wireless

how to write a config file to cisco 1200 B series Ap.how configure it.plz helpthanxmalli

We are currently using LEAP with two ACS servers (v3.0 & 3.2) in an NT Domain environment. We will soon be migrating to 2003 Active Directory. I am wishing to migrate off of LEAP but after researching I am still unsure what the pro's and con's are fo...

Hi, I am working with a 350 WGB, but when I tried to access it using a directly connected PC using a crossover cable I had intermitent responses from the WGB. Then I used a switch and a PC with the same results there are a lot of loss packets in the ...

I think there is a bug in IOS 12.3(2)JA and 12.3(2)JA2.That is with http/https authentication.This is my aaa configuration: aaa new-model ! ! aaa group server radius rad_adm server xxx.xxx.xxx.xxx auth-port 1645 acct-port 1646 ! aaa authentication lo...

Hi Folks,actually I was doing a password recovery and I deleted flash:config.txt, and then when I tried to delete /env_vars, I forgot to type the "/" character.So now the device doesn´t load the image. what can I do to recover the env_vars?? I anothe...

For rogue detection, I would like to be able to import all my switches on the network, we currently have over 400 with a mix of 3550's and 2950's. The way I see it you can only import switches on the network that have a wireless device hooked to it. ...

Hi all,I've a system, with several 1100 access points, that has two different SSID's in the same AP. One of the SSID is in "guest-mode" (broadcasting). I would like to know if it is possible to "move" a client associated with SSID "A" (guest mode) to...

In the association table for the "Entire network", I see a number of access points (AP1200s running VXWorks 12.04) with an IP address of 0.0.0.0. I am able to ping all of my access points. I know what the IP addresses for those APs SHOULD be. If I br...

I have a 1200 series Cisco AP set up do 802.1x and WPA. I can get my Cisco 350 series card to do 802.1x authentication with the Microsoft Wireless Configuration service started.However, I can't get the CB21AG-A-K9 card to do 802.1x or WPA. If I have ...

I am a little confused on what the difference is in the power settings for CCK and OFDM. The first issue is about settings for the site survey process. Being that the ACU utility is what is used during a site survey and it only supports B and not G, ...

Please tell me how to edit the supported rates list on an 802.11g ERP client (not access point). For lab purposes I would like to omit rates 1, 2, 5.5, and 11. The usual client utility appears not to support this configuration change.

Hi,Am looking for some advice on how best to determine my needs.Due to building restrictions (asbestos) we need to setup a Wireless LAN and I have utilised, for testing purposes, an Aironet 1210 with 802.11g Module. On top of that I had access to two...

Hi,here's the scenario ..... this is our first use of wireless bridging; we will be using two 1410 Wireless bridges to connect two buildings with multiple VLANS. A local Telco will install and manage the 1410s.My question is do we need to specify to ...

I have a new site to site wireless link we are trying to keep up. We are using the 350 Bridge with 2.4 Ghz, 13.5 dBi Yagi antennas. We have a relay point that we go through that has two briges with one antenna each. Each end point Bridge is configure...

I've read that this level 4 severity warning message indicates a potential error condition.A packet sent to the client has not been successfully delivered many times.I did not find a recommended action. What can I do to solve this problem?Thanks