Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello All,I am trying to configure monitor mode for the Slot0 only on Cisco AP 3802. But it seems there is no command to do this. I am using C9800-CL-K9_IOSXE, Version 17.12.3Appreciate some help and advice on this.Thank you !
Hello, everyone. When I was first studying for the CCNA, I thought we had two main methods of how users can be authenticated 1. Via PSKs in WPA Personal2. By using EAP, a RADIUS server, 802.1x, and so on in WPA Enterprise However, after labbing up th...
I am looking for antennas for C9124AXE APs and am having a hard time confirming AIR-ANT2524DW-R models work with C9124AXE APs. According to below document ,AIR-ANT2524DW-R is not included in「9124AXE Access Point Supported External Antennas」list.Cisco...
Hi all,I would like to get a clarification on this issue. The firmware update appears to be completed based on the provided screenshots. However, after verifying the WLC and APs over GUI and CLI, the version has not changed and still shows as 8.5.131...
Resolved! Cannot change AP country code
Hello,I have a problem changing the country code on the brand-new AP C9120ax. I've tested about ~20APs From GUI it's working like a charm but from CLI it does not. I'm trying this with no effect.ap name AP-NAME-01 dot11 24GHz shutap name AP-NAME-01 ...
Hi,We are configuring an N+1 redundancy setup with C9800-40 (IOS XE 17.9.4) and are currently evaluating the best approach for AP fallback configuration.We are considering two options: AP Priming and enabling "AP Fallback to Primary" in the AP Join P...
Hi all, I am writing CLI to block some MAC address. for example: access-list 705 deny 7831.c181.d8ff 0000.0000.0000 access-list 705 deny 4404.4470.a7a0 0000.0000.0000 access-list 705 deny c4b3.0118.5258 0000.0000.0000 But I took mistake for a MAC a...
Hi Team, I met a issue that the mobility tunnel can't be built between WLC3504 and WLC9800-40, their version meet the ICRM requirement, I suspect the issue happens since certificate using by DTLS, I saw the logging information as follow: -------...
Folks, I'm having a hard time determining if the C9120AXP access point and the AIR-ANT2513P4M-NS are compatible. This is for an internal warehouse implementation. I see pages that specifically state the C9124AXP is compatible, but that's an external ...
Hi,Network Setup Overview:I have deployed a wireless network using Cisco Business Wireless CBW240AC access points and a Cisco C1000 series switch. The setup includes seven CBW240AC access points, with one configured as the Primary AP and the remainin...
Hello, I would like to block a device on just one of my SSIDs. Is this possible? I currently have 4 SSIDs on my controller, and I would like this device to not access just one.
Hi all!I just want to know is there a way to configure rate limit for authentication and association request to prevent the flood attack, either on AireOS and IOS-XE WLC.As in my understanding, this type of attack aims to AP's association table if th...
I want to install c9800 in workstation The installed c9800 does not ping to the pc. Workstation (c9800) - switch - pc connected,You set up svi in the same band as the same vlan.I caught the gateway in c9800 with the svi ip I set on the switch. pings ...
Resolved! CW9176 and GPS
The Meraki CW9176 has a built-in GPS capability, allowing it to provide location information for self-location and associated purposes. If I have a challenging environment, where none of the APs (all CW9176) can "see" the sky, how can I get location ...
I can only seem to find ways to whitelist MACs, not deny MACs per SSID on WLC version 17.6.5.Any advice is appreciated.V/R
