Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! APs not getting IP
I have 3 cisco mr33 AP non of them get Ips from dchpI physically took one home and it still not getting IP in the dashboard it does shows ip but no connectivity and when ping that ip no replyThe one I took hoe still show ip from the subnet of the off...
Hi guys,1140 APs don't register with the 5508 controller. Here are some debug outputs:AP's IP: 100.31WLC's IP:100.2debug capwap events enable*spamApTask1: Nov 01 11:25:04.958: 30:e4:db:d3:a4:ca Discovery Request from 192.168.100.31:47690 *spamApTask1...
Hi, At what interval Prime Polls the wireless controller to get the wireless clients ? In the User Guide, I see it is mentioned as "Wireless clients are discovered from managed controllers or autonomous access points. The controllers are polled duri...
Hi all,I'm not sure about the settings of the"Antenna Configuration" for an 1852E Mobility Express Access Point. If I look at the datasheet for the 1852E, it notes that 2.4GHz uses 3 antennas. -> Does that mean that for Radio 1 only 3 Antennas need t...
And who is the admin of that organizationThank you very much.
Hi, Can we disable SSL2.0 TLS1.0 in Cisco Prime infrastructure ? If so, how ? I found the command to enable it, but not disable it.
Gents,Is it possible to disable workstation-to-workstation communication in a wireless network using Cisco ISE ?. I know it can be done in the wired network using dynamic ACLs. Regards,Edouard.
Dear All,One Access Point (2802i) has been joined to the controller already and working fine. But when I try to join other AP to the same controller it is not joining. WLC-9800 IOS : 16.12.1
AP1832 (Mobility express 8.5.151) TLS Version 1.1 Protocol Detection -> Enable support for TLS 1.2 and/or 1.3, and disable support for TLS 1.1.
Hi,I have a WLC 5760 v 03.06.08E and an virtual MSE version 8.0.150. the MSE is registered in Prime with no issues but the NMSP status is Inactive on both WLCs. I've tried syncing, removing, checked NTP, nothing works. The logs on the MSE are:July 1...
Resolved! AP attempts Discovery indefinitely.
AP attempts Discovery indefinitely.AP and WLC are good at ping.Can you find the cause?? (Cisco Controller) >ping 172.17.202.244Send count=3, Receive count=3 from 172.17.202.244
Hi, I'm trying to find out a definitive answer on whether or not the Cisco AP3702 will be compatible with Cisco ICE and DNA Center. We are considering upgrading to these platforms and have several hundred 3702's. We are currently at 8.5.151.0 on our ...
Hi, We are having an issue where our AP will not join any of our Wireless LAN controllers. Console output shows; [*01/18/2019 15:05:13.3086] CAPWAP State: Discovery[*01/18/2019 15:05:13.3088] Got WLC address 172.16.1.5 from DHCP.[*01/18/2019 15:05:...
hi i have a probleme i see my ap join my controller but disapear after 10 sec mabye AP6c41.6ab1.f28f#*Jul 13 20:42:03.239: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.222*Jul 13 20:42:03.239: %DTLS-5-ALERT: Received WARNING : Close notify a...
Does the AIR-AP1832I-E-K9 has the heat map feature ? if yes, how to activate it and generate reports?
