Cisco Developed UCS Integrations
Integration discussions, knowledge articles and more
347 PostsActivity in Data Center and Cloud
Upgrade Unity Connection 10.5 to 11.5 then 14.5
Hi,I'm getting a new server and want to migrate the config of the older version of Unity Connection 10.5 to the never server running 11.5. I have to do this in step due to compatibility issue. Afterward I will upgrade 11.5 to 14.5.I was looking at ...
Launch server KVM from FI Device Console while in IMM?
New to the IMM for UCS... While the UCS is connected and fully managed by Intersight SaaS, if I login to the FI A local IP for the Device Console and tried to launch KVM of a server, I got presented with the vKVM login page (screenshot below)...I do ...
ACI - Encapsulation and L3Out Problem
Can any of the experts here shed any light on an issue we are having, it seems remarkably simple yet I cannot seem to work out a way around it.We are migrating from the world of Cisco Nexus/FEX to ACI and we have one particular VRF that I cannot work...
ACI Multi-Site deployment with initial configuration and verification
IntroductionPrerequisitesRequirementsComponents UsedConfigure:Logical network diagramConfigurations:IPN Switch configurationRequired configuration from APICMulti-Site Controller ConfigurationVerifyStep 1: Verify infra configuration from APIC GUI on e...
Cisco Nexus 9000 with FEX modules random module disconnect
Hello everyone,Simple topology:Two Nexus 9000 93180YC-EX connected via VPC have 6 fex modules connected to them — 3 fex modules to each.All of a sudden out of nowhere one morning the modules started to disconnect randomly and later all ports on the s...
NTP ACI
Hello, can we configure ACI as NTP server? Providing outside environment with ntp info?
Cisco ACI Simulator 6.0-3d on error: SHA digest of file acism-6.0-3d-d
Cisco ACI (Application Centric Infrastructure) General Steps for the Installation of Cisco ACI Simulator: Download the OVA:- Download the OVA file from the official Cisco website or authorized source. Example of access with authorized login and pa...
Why does the Cisco UCS server not discover external storage arrays?
Hello, Cisco community,My Cisco UCS B200 M5 server is experiencing problems and does not detect an external storage array for the NetApp FAS 8200 connected via a Fibre Channel connection. We've tried a variety of troubleshooting steps, but the proble...
Track network traffic in UCSM
I have a huge number of vLANs in a UCSM environment which I believe are no longer being used and i would like to cull them so that only the used vLANs stay in UCSM. Is there a way to setup tracking for each vLAN so that I can see if traffic is flowin...
C220 M4 Boot iSCSI Target from embedded NICs
I have a C220 M4 that I attempted to boot from an ISCSI target from the embedded Ethernet ports.I can add the IQN with no issue.When a try to “Add an Attempt, I receive the following message. I checked the Network Stack – it is enabled, but I’m not s...
Resolved! APIC-M4 recommended software version
The Cisco APIC Installation and ACI Upgrade and Downgrade Guide recommends using a long-lived version 5.2(x) or 4.2(x). However the APIC-M4 doesn't support either - “The Cisco APIC L4/M4 requires the Cisco APIC software 5.3(1) release or later or the...
ACI L3out Multiple ExtEPG vs Contracts
For simplictiy, I'll refer here to L3out External EPGs by their external subnets, and I'm only asking about external subnets.What I'm concerned about is if I start with a contract that permits all traffic from ExtEPG_0.0.0.0/0 to some EPG1, and 2yr l...
Not successful Forwarding all logs in UCS to syslog server
Hello Bros' I have UCS system with Fabric interconnect 6248UP - Chassis 5108AC2.IFTA-FI - UCS Manager 3.1(3a). I have tried to send all system logs to a remote syslog server but still not receiving any. how syslog for the UCS works "UDP ...
Powershell: Cloning BIOS policy
When deploying new templates through Powershell I want to clone an existing BIOS policy and attach it to the new template. Unfortunately there is no clone or copy cmdlet. When I use the GUI logger to convert the api commands used to clone a BIOS temp...
Cisco UCS PowerTool Core modules v3.0.5.5 for UCSM, IMC, UCS Central
Cisco UCS PowerTool Core suite is a set of PowerShell Core modules for Cisco UCS Manager, Cisco IMC and Cisco UCS Central, that helps in the configuration and management of Cisco UCS domains and solutions. Cisco UCS PowerTool Core modules are develo...
