Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HiI’m planning to shift our office location to another so im asking about the ip cisco phones and cme that I already have , please check my below questions :I have the following parts regarding my central ip :Cisco SMARTNET 8X5XNBD Cisco 2911 Voice B...
hi everyone, i have Cisco router with voice capabilities and a CUCM working fine, but a department in my job want to use a asterisk PBX to call some people, they have a problem because the CUCM is sending a "taken call" signal to the asterisk instead...
We have an existing SIP/h323/CUBE router (ISR4321) that has been working fine for a years. We recently replaced the upstream lan routers and implemented vrrp. With vrrp enabled we have one way audio for any calls coming through the router. Intern...
Hi GuysI have problem with one way audio with SIP phones to particularly dial-peer. Calls from SIP to SCCP - works fineCalls from SIP to PSTN and from PSTN to SIP - works fine This is part of configuration that is related to SIP phone registration ...
Hi all, Can some one help me with the dial-peer config that i am goffing up on my new cube setup. Running config:- voice-card 0dspfarmdsp services dspfarm!!no voice hunt b-cap-unauthorizedvoice call send-alertvoice rtp send-recv!voice service v...
Hello, im having an issue with all Cisco 8941 phones and the Forced Authorization Code. Every other phone model 3805 is working ok with it when we try to call X number it ask for the FAC. But when we try with the 8941 phone it doesnt ask for the FAC,...
I have different types of Cisco IP phones 7975 7962 7960 7942 7911 6942 all of them are registered to CME 11.7the issue is when I press directories button to see call history(missed calls, received calls placed calls) I see "xml error 4 parse error" ...
Hello world, I have a question regarding the dial-peer matching mechanism with the preference command enabled. Here is an example: "Incoming" dial-peer voice 1 voip incoming called-number 3004. session target ipv4: x.x.x.x "Outgoing" dial-peer ...
Hi all, I want to modify codecs in the dspfarm profile, after shutdown the profile and try t modify the codec removing one of them I got this: profile oper state is down in progress, please wait for some time and retry I try to no shut the profile bu...
Hello Experts, I have a question that if ISR can select dialpeer when detected some specific sip codes Such as 404 or 503. I'm not saying about the SIP OPTIONS, i mean in some cases the remote side can properly respond options messages but for some c...
hsh-io-4431-01#sh call active voice compactcallID A/O FAX TsecCodec type Peer Address IP dp VRFTotal call-legs: 22449142 ANS T528 g711ulaw VOIP P6028016807 10.20.71.73:1 7306 NA2449143 ORG T528 g711ulaw VOIP P18662155511 67.14.92.85: 31400 NA How t...
Hi,Whilst I've setup and used VoIP at work (IT support role) with a small range of handsets and PBXs, I though it was time to have a play with some other devices at home (with a view to going VoIP at home).I've recently acquired an ATA187 and a CP-69...
Hi Guys, I am trying to setup a SIP Trunking from our PBX Which is Broadworks and to 2811 CME Router. Broadworks <--> SBC <--> CME sip-ua are now showing registered.But, When I do a call to the Pilot number, it shows that the CME router is sending 48...
