Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am trying to implement SIP EO on trunk from CUCM to CUBE.I enabled SIP EO in sip profile (Insert MTP if needed)To test I use CIPC version 8.6.5.0.I notice diffirent bihavior when calling from CIPC over SIP trunk.When I enter number and press DIAL b...
Hi everyone, If I am able to calculate the number of UCLs I need when migrating from DLUs to UCLs, is it enough to create a request via PLM and send the request to Cisco without a report from the License Count Utility?
I am migrating the current 8.5.1.10000-26 to virtual platform with ESXi. On this case the MAC will be different so I would need another license file. But is possible download the current .lic file from the physical cucm? I have found only the option ...
Hi I have CME with two IP Phone IP Phone1: 172.16.15.5 CME: 172.16.15.6 IP Phone2: 10.10.10.2 IP Phone2 have 10.10.10.2 and after NAT have 172.16.15.8, the problem I faced is the phone 2 can ring but not receive any Media only send, How I make Pho...
I am working on a system where they have 1 analog line plugged into their H323 gateway, we have set the caller-id enabled on the FXO port and when we do a "Debug VPM Signaling" we can see the caller id of the phone as it hits the voice gateway. Howev...
Hi It looks like only one softphone can be installed on one PC. I tried to install two, but failed. How do you think about it?
Hi How do I set buttons with numbers or personal extensiones. As speed dial. Model 7861 phone Regards. http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/7821_7841_7861/10_1/english/user_guide/PA2D_BK_UB7EF0F0_00_user-guide-7821-7841-7861/PA2...
Hi there we are looking for a setup to get the following workflow, we are using CUCM 10.5.2 and Jabber Clients 11.5.1 for Mac -> we have a pickup group "dept-a" with 5 members. group pickup notification, pickup as such works fine.if one of the member...
Hi everyone , i need help to resolve the issue (i have router c2851 with 4FXO and nme(Cue 3.1) +cme )what i need if any income call from pstn, the caller he listening the specific message audio and after that transfer him to internal number in my net...
Dear All, The gateway is mgcp. The phone behind it has number 4082022002. When making a call at 2002 and 2022002, the phone can get a bell voice. but if making a call at 4082022002, the phone cannot get voice, but I can get it debug message as below....
Hello everyone .. I have a client who has 20 IP phones (9951) with camera module, and wants to connect them to an existing CUCM 6.0.1 I checked on Cisco website and it says minimum requirement is CUCM 7 I was wondering if I can connect them to CUCM ...
Using a Cisco 2901 ISR configured for H323 connecting to CUCM 7.x - Using H323 for caller-id support on the FXO ports. It's a VIC2-2FXO and both inbound/outbounds calls is working fine. However, when an inbound call is made and not answered, the FX...
Hi,I'm facing problems while trying to define softkeys (e.g. transfer or dnd) for the 9971 with cme 9.1. 1. trying to define softkeys by specifying them in the voice register template command doesnt workvoice register template 1softkeys idle cfwdall ...
Hi All, I use SIP Phones 7841 i have configured all sip phone same configuration 2 IP Phones (1004 and 1005 ) work right but the rest display problem "Unprovisionned". what is the prroblem? Thanks in advance voice service voip allow-connections h32...
One question!! I have one cluster CUCM version 11, in the table Device -> Phone (image cucm list.png), no appears parameters as CSS, owner user, its posible add this items at the table ?? Thanks!!
