Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Community, and thank you in advance for reading my problem.I have a lab CME Setup using an old 2901 router with CME Version 11.0.I have a couple of sip phones, and I have been playing with 2 basic sip trunks.On one, it works fine. Inbound and ...
Greetings, have a client who wants to do the setup as below. Firewall - int 1 to switch for data vlan, int 2 to switch for voice vlan (both interfaces have been configured with DHCP scopes separately. connected to switch on trunk ports. CME is also c...
CIPC Verison 8.6.6 intermittent crash during use. Steps that have been tried. Complete wipe and reinstall (From older version it had issues as well)Updated all drivers New Headset Other Info I'm not on a VPN connectionI'm connected via hardwire to t...
Hi,I received some brand new CP-7821-3PCC-K9, but I use CUCM 11.0How could I change the MPP to Enterprise?Is there any way to upgrade those firmware?Many thanks.
Hi Tech People,I have two Voice Gateways (A & B) & CUCM (Pub/Sub)I have 2 PRI Lines with 500 Numbers from one Provider. Currently 2 PRI Lines are connected to Voice Gateway A. PRI 500 numbers are distributed in 2 PRI Lines.i want to configure the fa...
I have BE6K with firmware version 10.5 and I want to upgrade this Firmware to 14 and I have old ip phone model (7911,7912,7941,7960, 7970) also, what is the best practice for this Solution Cisco Business Edition 6000H/M (M5), Release 14 Can Integra...
hi I have a cme 2600 router and a 2950 switch and I configured them as voice and data in a small company in the company I have voip hosts and phones and everything works correctly, but now I brought the internet line and the voice line to an urban dw...
Hi Team,We are using Cisco 3905 IP phone .We are getting issue while dialing the ext. number of End user . I can see only Extn no. is visible at my end IP phone display , dialed user name is not showing with ext. no. Please suggest how can we get bot...
Hi,I'm trying to get 2 phones (analog phones connected to a Linksys PAP2-NA) to register on CCME. These phones are located in a remote network and they are able to reach our CCME over a L2L IPsec VPN. Site-to-site connectivity is fine, router configs...
We have Cisco 8851 Phones in our office. I am noticing that all the lines display 10 missed calls. I have gone in and deleted the missed call history from my phone but it is still showing there are 10 missed calls on each line. How else can I try to ...
Hey All,I have a project in the coming weeks to move ~2,200 Lines Over from a CM6 to 16 VG450s.Back in 2017 I was able to migrate ~125 analog lines from a legacy Nortel system to a VG350. I have some of my files from back then but nothing is clickin...
Hi,I have a Cisco CCME with a SIP-Trunk to an external provider. Incoming calls over this trunk are forwarded to a Cisco Unity Express IVR (running on a SRE), which - depending on the users DTMF choices - forwards the call to the chosen internal exte...
We would like to use a two features Trust Relay Point (TRP) and a Cisco Unified Border Element (CUBE) co-resident on a same router ISR 4431. Does anyone know if there are any limitation and/or impact (CPU, RAM) ? Is there any documentation available ...
I have the Plantronics CS540 and a Cisco phone 8861. The headset turns off about 30-45 seconds after a call is started. My e-hook headset is enabled which is what other users with this problem have encountered. Any advice will be greatly appreciate...
When trying to press * or 4 during cisco greeting from an external caller it is getting ignored. Internal works fine.I read somewhere about the voice gateway dmtf settings but I believe I have all the correct info.Here is some of the running config o...
