Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am able to make the local call in iphone/Android device,when i try to make a call from Window client iam facing issue on only local calls to mobile,,,,but when i tested in deskphone i am able to complete the calls..,can any body suggest me on this
Hi !I have a use case that I have been thinking about. Please see the attached sketch. Could you have a cube (or any other form of voice gw) dynamically register sip ua:s with authentication over radius towards a user db?What I would NOT like to have...
CUCM: 8.6.2.21900-5Call Manager page shows PRI as unregistered, however on gateway ISDN status is Multiple Frame EstablishedISDN Serial0/0/1:23 interface dsl 1, interface ISDN Switchtype = primary-qsig **** Slave side configuration ***...
Hello all,I am techinal engineer, but i need to make BoQ for 3945 CME-SRST for one of our client.In Cisco Commerce Workspace i can see there are two types of 3945 routers are available for CME SRST1- C3945-CME-SRST/K9 = 3945 Voice Bundle w/PVDM3-64,F...
I have a problem with inbounds calls from an IP PBX to a callmanager 7.X. The call can not be stablished. This is the capture log of the call ***************************** SIP message buffer start ***************************** INVITE sip:172.24.164...
Hi Folks,I have an issue in a new Voip deployment whereby when a user call forwards their internal phone to an external mobile, the site prefix is being added to the Originating caller ID on the destination mobile phone and trailing digits are stripp...
Hi,We have IP telephony setup with CME 9.1 with 2921 ISRG2 router.Client would like to take ISP SIP trunk.Do we require CUBE license for the same.Because I tried in the 2851 router without the CUBE license and its working fine.How I can check CUBE ...
Hi,I want to know part number for ordering CUCM licenses for 7942 IP Phone.Is this part number correct SW-CCM-UL-7942= ??Thanks.Shakir
Hi, i have finished the upgrade if cucm to 9.1.2. I have 6 h323 gws 2811 with 12.4.22t ios, in the lab everything is ok. My question is can i move to production and later i can upgrade memory and ios of my routers or it is more likely to have problem...
CME integrated with CUE. when i place a call from outside to office where CME is configured. i listen two rings before welcome message.i want to listen welcome message as soon as i dial the office number without rings.please help me to sort out this ...
Hi All,Trying to get an EFTPOS machine working connected into an FXS Port using SCCP/STCAPP Protocol for call control.The port is registered in CUCM, I can connect an analogue phone to the port and successfully call the Bank's 1800 Number etc, I can ...
There are a number of clients where the duplex settings on their ip phones are set to 100 full duplex instead of the default selection: auto negotiate. I'm sure they did not change it themselves. The IP phone model is CP-9951. What could cause this c...
All,I am experiencing issues registering my IP phones with CUCM 9.1 since the introduction of a FW. If you see the attached diagram we have added a firewall put the DHCP server on an interface in a seperate zone with option 150 an since doing this t...
Hi, If the publisher is down (hardware replacement), i can do changes such as i can add phones, adding features,adding services, in subscriber or the subscriber is only in read only mode??? In 6.X is it was a read only or read write.???If my publish...
Hello all, Central site CM with many remote sites. Currently all phones are registered to the Central CM with CME as SRST at the remote sites. Is there a way to have the phones register to CME as primary with CM as secondary but still do all the pr...
