Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello guys,I have configured BLF Speed Dials in CUCM v9.1 but I'm still not able to configure them from the users web access (they just don't appear in the ccmuser web access), does anyone know if it is posible in this new version???With regular Spee...
Good day,Have the 2851 cisco with cme 7.1I have to dial-peers to external trunks. To one dial-peer calls going through prefix 9 and another to prefix 5. We have 5 sccp phones that should can go only through dial-peer with prefix 5. So I want to chang...
Hi Everyone,I wanted to check if there is any way to pull a report (from cucm) which gives us the number of users currently logged in from the cisco end user pages to manage their phones - is there any way we can find this out? Thanks!Atul
Hello,I have a 7961 phone with the following loads: SCCP41.9-0-3S.I want to install the phone with a customer who has CME but with a lower loads file: SCCP41.8-3-2S.loadsWill this cause any issues? Initially the phone didn't boot at all, so i connect...
Hi to everyone,Does know anyone if there is a 3d party IPhone SIP Client compatible for UC500 that works over VPN?Thank you!
In all of the examples I have looked at in the QoS SRND and the Medianet Campus QoS Design 4.0 guide they show inbound VoIP being policed at 128kbps and inbound signaling being policed at 32kbps on the ingress switch port. None of the examples reall...
Hi,Until now all the sites used u-law where i worked. I have a requirement where one country telco uses a-law standard. Is there any configuration that i need to put in place on the VG to support a-law or the ISDN PRI does the voice encoding
Hi I have a CUCME 9.5 and I am unable to save the config from the GUI. I get the message other telnet session active. I seem to remember this was a bug in earlier versions is this the case in 9.5.
hi all, I have cisco 6921 Ip phone installed in my network, when ip phone received 4 to 5 voicemail ip phone was got hang and MWI notifications is auto blinking.kindly help for this issue
HII all, I Have set up mobility profiles for metting rooms, and are workign fine the problem is I do not have an option to logout of the profile once signed in I am using Cisco IP Phone 7940 series. I must be missing a setting somewhere can somebody ...
Hi All,We have CUCM 7.5, MGCP gateway deployed i am facing below issue request you guys to guide me to get solution for this.•1. We have route patters with calling party transformation as belowPrefix: 0110112•2. When we call from extension 1230 using...
Running Unity Connection 8.6.2.I set up a call handler to serve as my auto attendant for the office. I configured caller input '5' to leave a message and send the message to a user with a mail box. The user receives these messages, but they do not ...
Can anyone clarify exactly what the command "max-presentation number" achieves when configuring phone templates in CME?In the comand reference it states it is to set the number of call presentation lines supported by the phone type. I have no idea wh...
Hi we are using c2851(CME) with CUE version 8.6.4 and cp7965g ipphones(firmware 9.3.1). we are getting some vulnerability messages which i attached the report. so we have decided to disable http in Cue and ssh in IP phone. can you suggest how to disa...
Hi, How to setting CUCM to notify or alert caller to know when destination number in use.Senario --------------1. Mr A and Mr B use phone Mr. A <-------------Connected-------------> Mr. B3. Mr C make call to Mr B Mr. A <-------------Connected--------...
| User | Count |
|---|---|
| 7 | |
| 5 | |
| 5 | |
| 4 | |
| 2 |
.jpg "VIP Expert"){kind=icon}
