Dear guys. I'm using CME 8.6 in my company.I'm facing an issue of paging. Here we use ext7500 for paging. Some user page to that number and sometime they forget to disconnect that call. So the othe users couldn't make call. Is there any option ...
Dear guys. I'm using CME 8.6 in my company.I'm facing an issue of paging. Here we use ext7500 for paging. Some user page to that number and sometime they forget to disconnect that call. So the othe users couldn't make call. Is there any option ...
Hi First Question :How i can call directly without pressing 0 or 9 on the phone ?? i have h323 protocol this is POTS configuration in My gateway : dial-peer voice 11 pots destination-pattern 9.T progress_ind setup enable 3 progress_ind alert enable 8...
Hi all,Please I need some help to understand how to order the UC560 in the following scenary, and the questions are:scenary: UC560 Principal Site A with 30 Analog phones (Using VG224 or ATAS) and 20 IP Phones. NO Analog trunks Just SIP form the...
Dear I have a Fiber coming from Telco or MOC , this fiber going to My Switch then going My Voice Router (with 2 Analog and one E1) as "SIP Trunk" with CUCM 8.6 .My Questions are : 1) what I will configure in the intrface in Switch that is going to V...
Hi,is it any way to know my CDR Repository Manager operation status wether is it successfully send the DATA to billing system server or not?Or anyway to sent the alert through email while the operation is fail?thanksThor
hi,currently i have cucmbe 8.6 and registered 9971, 8941 and 9951 phone. Camera of 9971 and 8941 are working fine but camera of 9951 is showing message on phone screen "Cisco Unified Camera detected but disabled by the administrator". Even though i ...
DebugHi I have CUCM8.6 and Voice gateway that are connected through SIP Trunk to Teleco or MOC it is giving me bust tone when i am tring call outside through sip trunk Note : E1 module and FXO module are not used or not available , the call is going...
System- CUCM 8.5.1SU2, H323 Gateway 3845 -IOS 12.2(22)T4Previously I can see ip address of H323 Gateway on CUCM and I can ping from both side. But when I add more dial-peer and route pattern point to that H323. I found that it cannot make call from b...
I got 2 phone numbers (DID's they call it) from SIP provider Flowroute.com using an internet connection to a ethernet WIC card in my 1760 CME. I successfully setup my 1760 CME to register with Flowroute in the SIPua config. I can m...
Hello,According to 7965G user guide, 7914 modules are compatible with new 79x5 phones.I've tried that and 7914 buttons stay red. The 7965 is well configured with a module type of 7914 and a template with BLF on the module buttons.The phone version is...
Hi,how can i add some extra digits without informing users. Lets say if users dialing 90501234567, at backend, i want to add 9088880501234567.
We are implementing the integration of Nortel PBX with Cisco CUCM 8.6 using QSIG trunk.When Nortel phone calls Cisco phones, if Cisco phone doesn't answer, the call gets forwarded to voicemail (Unity Connection 8.6), then Nortel PBX generates an erro...
OK - This is a little bit weird, but I'll do my best to explain the scenario......Here we go.....I have a customer that has a current Nortel PBX, customer has given me 4 analog lines (extensions 100,101,102,103) off of his Nortel. ...
I have 2 routers 2801 use IOS: c2801-ipvoicek9-mz.124-24.T7.bin. But when I insert the VIC-2FXS it don't use this card. What's the problem.VIC Slot 0: FXS Voice daughter card (2 port) WIC module not supported/disabled in this slot ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-21-2025 07:42 AM | ||
05-21-2025 06:23 AM | ||
05-16-2025 12:03 AM | ||
05-12-2025 12:06 PM | ||
05-12-2025 06:55 AM |
User | Count |
---|---|
5 | |
4 | |
2 | |
1 | |
1 |