Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all, Please can you share the procedure to install and upgrade the language for Ip phone. thanks.
Good day all,I have a requirement to force all phones registered to my CUCM (11.5) to un-register and re-register to the call manager at a minimum of every 3 hours. I don't even know where to start on this one. Any help would be greatly appreciated.T...
Good Morning ColleaguesI hope you are doing good and safe. I have configured 2 dial-peers , One for VOIP (SIP trunk to third IP PBX) and another POTS for outbound/incoming calls to & from PSTN. The extensions at the third party IP PBX are 1xx . So i ...
Hi guys,I just jointed a company which uses Cisco IP Phones. I have a Cisco IP Phone 7942 which not seems to be booting.When connecting the phone all lights are blinking as on any other Cisco IP Phone,But on this phone the screen/menu is not loading....
Good Afternoon ColleaguesI hope you are doing good and safe. May i know if "vwic-2mft-t1/e1" can be used for E1 voice or E1 data only? Best Regards
Hello,we have deployed on-premise Cisco Jabber 12.9 and we get the contact's picture from AD successfully but the user's picture is not showed in "My profile and settings"we have tested Cisco Jabber 14.0 too.our jabber-default.xml file is:<?xml versi...
We have Cisco ISR4331 with the following IOS and CME versionIOS Version: IOS XE Software, Version 16.06.04CME Version: Version 12.0 (SIP)We would like to know if the following version of SDK is compatible with CME version in order to develop the inte...
Hi community, I have a problem with CP 8865, sometimes when users are on a call their phones reset, even when the phone is on hook, checking phone logs we realized we have the next out of service codes, [17:56:51 01/11/17] DeviceTLInfo DeviceNam...
I've enabled my Jabber as a remote device and there is a custom E911 Message created in CUCM. Do I need to alter the jabber-config.xml or create a https redirect? Other than the below documentation, I cannot find alot of information on this. I want t...
CUCM 12.5 is sending only enbloc to all destinations and if dial digit by digit it will reach only to third digit.Pls. help
Hi, we are trying to download the APIs for CUCM, however we are not able to do that, when I click on the link, it prompts "page not available". http://www.cisco.com/web/developer/cucm/content/download.html Please assist. Regards, Navinder Singh
Dear all, I'm having a hard time registering Asterisk server with CME i tried this configuration with no luck(Asterisk IP:10.1.1.81, Router IP: 10.1.1.10): voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 address-hiding allow-connec...
Hi AllIf I want to enable the web page on all my cisco phones, can I do this under the enterprise phone configuration and just tick the box?will this cause any issues? will I need to do it out of hours? will it reset the phones?Many thanksCarl
Hi all,We are facing issue with outbound call. If we are calling any mobile number from jabber and called party is directly disconnecting call (without answering) call keeps on ringing around 30 sec. It's not disconnecting instantly.I can see in GW d...
Hi, I am in the process of adding a number of Cisco phones (7841s) to a HP-1820-48G-PoE switch. The switch supports, and looks to be configured for LLDP-MED, but is not putting the phone in the voice vlan, and extending the data vlan to the switchpor...
