Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Friends,I apologize in advance if this is a basic question. Due to employee turnover I just inherited our Cisco Voip system....What I thought was a very simple task is turning out to be harder than I imagined.I have a multple line phone and I w...
HI all !I have a task to get the wireless conference phone. I use CUCM 8.5(1).At the moment the only possibility is to have the third-party wireless spider (conf) phone as Polycom or Konftel and connect it to analog extension via ATA 187. Two questio...
I've set my 9951 display parameters as:Display On Time: 08:00Display On Duration: 00:00Display Idle Timeout: 00:10Display On When Incoming Call: EnabledBut the display does not come on when the phone rings.Have I mis-understood the paramters, or is t...
Hi,i m using a CUCM 8.5 , with 2901 voice gateway.I have a problem for incoming call. i tried to start tests by usin the " csim start command " to make a call from a Voice gateway to an internal ipphone registred with the CUCM.i repaet that command m...
Hi Guys,please dont you know, if there is a chance to change severity of remote syslog messageswithin CUCM 7.1(3) ? I would like to log severity lever "errorr" but besides important messagesit logs many useless ones (by these ones I would like to red...
I have this confusion regarding icomm exam.Where i can get actual study material and dumps.I heard even cisco did not released its complete guide.Any who wrote exam pls do reply???
Hi allI have installed uccx 8.0 nod1(pub) and nod 2(sub) everything working fine but one pblm is I cant login os admin page in sub same in ssh in sever .but no pbm login in pub os admin apge ,I have able login in webinterface administrtion page pub a...
Hi all,On a partiular 2821 Cisco ISR which is equipped with multiple C5510s which are configured for transcoding, we have a recurring problem with distored voice or choppy voice when calls are transcoded from G711 to G729.I can see from the IOS that ...
HiNew to Cisco IP Telephony. Requesting answers on - We got Cisco 3825 series Router can someone recommend IOS for the RouterWhat other software do we need to run CMEWe got 7960, 7940 series cisco ip phones do we need to download any software to regi...
Dear Friends,The Cisco Unified Communications Manager Express has been connected to PRI Line with Pilot Number.We have seen suspected toll fraud calls using the Cisco Unified Communications Manager Express IP Based PABXSolution. The IP Based PABX is ...
Hey guys,I'm having a real tough time trying to get a Cisco 7960 IP Phone loaded properly. I bought this one off eBay (which may be the problem right there, but nonetheless), and I'm trying to register it with my home lab. I know all the settings of ...
router#sh runn | sec fallbackcall fallback activecall-manager-fallback max-conferences 8 gain -6 transfer-system full-consult ip source-address 10.1.209.1 port 2000 max-ephones 250 max-dn 500 dialplan-pattern 1 905........ extension-length 11 cor inc...
Hi,I have a customer he has a CUCM 7.0 and he asking now for voice mail with Auto attendant and Call recording, Is there a solution we can combine all this feature in one application or he has to buy separate application.Regards
Hi,We have Cisco - Nortel integration using CUBE. We have configured media flow-around on CUBE.After configuring media-flow around we observed that nortel to cisco call is working fine. But when we call from cisco to nortel, we are not getting voice ...
I have have 2 UC series boxes connected via SIP dial-peers. Read as simple site-to-site peers.Box 1 has an FXO port connected to the PSTN.If a call comes in from box 2 via the SIP dial-peer, with digits matching the destination-pattern of the POTS d...
