Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We have followed configuration steps included in cisco unified communications features and services guide, call display restriction section, but is not working. We have CUCM 6.1.2 and ip phones 7911, 7940, 7942, 7960 and 7975. Any ideas what is wrong...
I am having a problem getting my 2821 gateway to register with a SIP server.I am able to use a publicly available sip client to verify the username/passwordthat I am trying to register withThe public client (xlite) seems tohave no issues and registe...
I have freeftpd installed on a server that backs up call manager every day. I am running SFTP as a service on that server, but when we log off the server SFTP stops and CCM cannot be backed up.Does anyone know of any SFTP software that cisco recommen...
HelloI have trouble configuring the CME / CUE because the LED display, voice mail does not work properly when the user receives messages (the lamp does not light)Here I leave the sh run of the CME / CUE.Thank you for your help.
I have a standard vg204 box runing sccp. i have connected at analog phone to port 0/0 and configured that port in cucm. Analog phone op port 0/0 number 222 is to call IP phone 952 when picked up. It works as expected.BUT when i hang up on my IP phone...
Hello All,I am fairly new with CUCM and need some advice as to how I can efficiently provide my users with the solution they need.I have extension 7080. Depending on the time of day, I need that extension to forward to one of three extensions.Betwee...
Is there a way to change the forwarding of a number when not on a phone attached to the Cisco UCM cluster? For example let's say currently DID 650-555-1234 which goes to UCM forwards to my cell phone at 650-444-5678, Now my shift is over and I want...
Hi All,Am experiencing a problem with my telephony network consisting of satellites site with CCME and a central site with CCM 4.1. Intra sites calls go fine, but inter-sites calls ring, get connected when picked up but no voice can be heard.This is ...
I was wondering if anyone could solve my problem. Im currently trying to set a group of 9 Cisco ip phones 7940 to an network to where they will be able to call within the group but have no outside lines. The phones in question are all several miles a...
Hello,I have a Cisco 2811 gateway with a E1 card installed (used with CUCM 6.1), I set up voice translation rules so that i can have direct lines. The problem i have is that when i call from landline phone it works great the line is redirected to th...
Hello All,I have only one question about CF card,1: CF card means flash of router or any expandable card ?Thanks
Hello,i'm testing bladeware vs. cisco gw. If i try fax trough t.37 all is fine. But if i send fax through t.38, i have trouble with ports. First is opened RTP stream and then is negotiated fax transmition with t38. All is fine, but my gw chose new po...
We have several 3845 voice gateways at our various locations. Many of these have several different PRI connections and most are running H.323 protocol. I have been looking at the CDR Analysis and Reporting area in CUCM Serviceability and specifical...
Hi All,I have a Linksys WRT54G connected to the Internet and the following ports are enabled:5060-5061 SIP16384-16483 RIPThen there is a Linksys SPA2102 connected to the WRT54G. The SPA2102 routes to the Internet (e.g. there is a computer connected ...
Hi guys,we have a issue with standard local route groups.Is it possibile, that QSIG-features, like calling name presentation, don't work with standard local route groups?If i associated a routepattern directly with a Route-Group (the same as the conf...
