Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All,I have a problem that i can not find an answer to, the below command gets rejected by the router, with the error invalid hostname or ip address.mgcp call-agent 01cucm 2427 service-type mgcp version 0.1Does IOS software not support hostnames th...
hi,we have an vg224 configured with SCCP and bound it to a CUCM 7.1 first and a 2821 Gateway as second. Works fine.In case of srst the vg224 ports works fine. But now the question: At CUCM I configured not all ports of the VG224 with a device pool wh...
Hi all,I am looking into deploying Unity Connection 7.x with a Pub and a Sub connecting across a WAN link. I've gone through Cisco design doc regarding Unity Connection cluster requirements and the requirement is rediculous. Cisco wants a 50MB lin...
Hi,We upgraded to V7 and I can't figure out how to move phones from one subscriber to another. We have to reboot after a feature was installed but I want to move the phones before I reboot. What is the best method in CUMC 7?ThanksMike
I have a Unity UM Version 7.0.2 ES20 enviornment with Exchange 2k3 as the message store, and the partner server. Some exchange 2K7 message stores need to be added. Partner server will remain 2K3. Is there a version of DAD that will test against 2K...
I can configure a Router as MoH Server, and add it to the Call Manager as MoH Server?
Is there a way to view the serial number for the Cisco MCS server (running Cisco UCM7 for example) remotely? I'm not on-site to do this. Any help would be great.Thank you!
Hi,On a CallManager 7.0.2 I have to make statistics on line group members answering calls.In service parameters I changed the option "Show Line Group Member DN in finalCalledPartyNumber CDR Fields" to enabled but in fact, in the CDRappears the phone ...
Okay, need some feedback on my perception of transcoding and how I plan to implement. Overview;- Default codec for all phones connected to a cluster is g711- One site (site B) is remote and has limited bandwidth WAN bandwidth to the main site (site A...
HelloWe have a site where users are not hearing any ring back when they dial a PSTN number. They hear silence until the remote end picks up and see Ringout displayed on their phone.Call Manager is on v 7.0.2PSTN Gateway is a 3845 ISR running Versio...
Hello All,I have a 7914 expansion module which i am trying to connect with ip phone 7962. I have read the release notes for 7962 with 8-5-2-SR1 firmware. It says that it needs to have S00105000400 which i do have on the expansion module.What happens ...
HiNeed to remove "TO" and "FROM" when calling to ip phones.when phone A Calls Phone B.its showing on Phone A Screen " TO A " and on phone bits showing "FROM B".I don't want to display this TO AND FROM on the cisco ip phone screen How i can remove t...
Hi There,I am trying to configure background image in cme for 7965 phones but don't see any document on that other than 7970/71/75 so therefore i'm curious whether is it doable or not?any input will be appreciated.RegardsMuddasir
I've received a couple of alerts from RTMT for "Routelistexhausted" coming from a Route group that uses a full T1 PRI. It would be very unlikely that the site with this circuit is using the entire PRI and CDR only shows about 7% utilization at the t...
HiI have a CM 7 lab and OCS R2 LabI want to integrate the two,I can't seem to find the documentation for setting up the integration with and without cucimocanyone?Thanks
