Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
It is possible to Lock Cisco IPPhone without any workaround [ Now I am using EM as workaround to lock and unlock IPPhone ], Please share you idea for locking IPPhone in CUCM and CUCME.
Hi There,Is there a way to monitor who is logged into a hunt group, I am having problems with users logging out of extension mobility but not logging out of the hunt group.It appears that they stay logged into the hunt group and calls appear to go to...
If I transfer outside call to an OPERATOR directly, there is no problem.But when outside call trasferred to TCL-AA, FXO disconnect problem ocuurs.I observe the same problem with CUE also
Hi all, the problem is that a 7961 phone doesnt anwser the calls when you lift the handset, you have to press the "anwser" softbutton, is not the first time that this happens to me, you know if this is any kind of configuratios issue or is just a har...
Hi,we use CUCM 7.1.3a with the feature Cisco Call back. Now there are some social security risks (observing people). We are adviced to allow only the feature callback busy - the feature callback no answer should not be a possible choice.Question : Is...
Hi, need to confirm whether MCS 7845H1-CCE1 is officially supported for CUCM 6.1/7.x [ i have installed CUCM 7.0.3 on 7845H1, but need to confirm that's officially supported], can't find any BoM or hardware compatibility matrix at Cisco site for CUCM...
Hi,I just installed CDR Analysis and Reporting (CAR) from CCM plugin based on cisco documentation. The CCM version is 4.1(3)sr8a.After going though the installation, I go to CCM serviceability > Tool > CDR Analysis and Reporting. And the browser popp...
Hi,UC520 log files are UTC time, sh clock has the correct time, deleted and created CNF files, didn't help. Rebooted UC520 and log shows that clock was updated from UTC to CST, downgraded fron 12.4.24T to uc500-advipservicesk9-mz.124-20.T2.bin, no ch...
Hello,I would like a way to have my blackberry device register to callmanager and act as an ip phone when it connects to a WLAN. I have found conflicting reports in other forums that this is possible or not.I have read about the mobile communicator ...
hello - i was going to set up a test environment using a 7404 and configure it as an mgcp gateway but when i went to add the gateway to call manager i realized there is no option for 7204 and mgcp. so my question is " how can i set up h323 at a branc...
We use CME. When users attempt to place an outbound call, they only have approximetly four seconds to complete the 10 digit dailing. Beyound four seconds, a busy signal is generated, thus, unable to place the call.We obviously need to make an adjustm...
Hello all,Forgive me for my lot questions about auto-attendant,In this link: http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/command/reference/cme_t1ht.html#wp1020031Cisco say that auto-attendant dont use consultative transfer and it use blind tr...
I am having problems getting a MGCP gateway to register with CCM (vers7.1.2).This is down to the network using VRF and the route to the CCM not being found.I have seen on some old discussions regarding MGCP not being VRF aware, is this still the case...
CCM 7.0 is required to integrate with a 3rd party billing system, what configurations required in this regard on CCM.What are the pre-requisites for billing system to be compatible with CCM 7.0?
I've been asked to look into whether or not certain phone features like last-call return (*69) etc. work through our phones. I set up a route pattern for *69 and it works, although it takes a while to dial due to the fact that it's only 3 digits. I...
