Hello all!!!I have one quetion , maybe somebody knows. Which Cisco equipment supports dynamic dsp conference and transcoding resource?Idea to insert one big device and dinamicaly allocate dsp .
I was reading the CM 6.1.2 Release notes and there is a step below-Step 3 Use an md5sum utility to verify that the MD5 sum of the final file is correct.Does anyone have a suggestion on a particular utility that they have used.
Hi Guys,Have a situation when calling in from the pstn the calling party does not hear the destination phone ringing but only them pick up.Added the voice call send-alert which sorted that out but it is still happening on internal calls between exten...
Hi everyone,I've got an ISDN line with around 8 MSN numbers connecting to my BRI 0/0/0 interface.I'm trying to configure the interface to answer only specific MSN numbers, but can only find the option to answer up to 2 numbers using isdn answer1 <num...
We are looking at using Host Monitor. other than calling phones listed in call manager and checking your voice mail, is there some services we can check to make sure eveything is working as normal with a remote monitoring program?
After installing a WS-X6624-FXS card in our 6509 switch, the card was recognized by the switch but shows to be in a "PwrDown" state. I'm aware this is an old card and is EOL, but we'd like to use it if possible. Have found some notes about IOS vers...
Dear Seniors.This is regd call park. when i retrive a call after parking, it is getting delayed for 4 - 6 seconds for retriving it.After dialing the call park number, it takes 4-6 seconds to retrieve the call. What could be reason. where to check, wh...
Hi Probably a really stupid question but....I have CME everything is working fine however all incoming calls are showing up as unknown number. I have searched on google but all I could find was to use the caller-id enable command on the voice ports h...
Hi,I have got Unity connection 2.0.1.2000-337 integrated with CCM 6.0.1The problem is that when a user leaves a message MWI does not come one.I have dialed the MWI numbers and both on and off works fine.I did enable micro trace and attached here are ...
Hi,how do i configure 2851 CME router with VWIC-IMFT-E1 to recive Calls and another VIC-4FXO for otgoing calls.any one can please help to setup this .please find my sho run configuration here
Dear all,I have a pbx and cisco 2821 with vwic.i want to OPX on my router.So on my pbx cas is configured with 30 specific number. on router side i have configured 30 seperate DS0 channel to achive 30 dedicated voice-port.i have als0 30 FXS port on my...
I've seen some other threads on this.. but all are old.. Environment:> 5.1 CUCM box with a PRI to the PSTN.When a call is forwarded to an extension off site [say cell phone], the incoming calls to that cell will display the Caller ID for the office e...
Dear allI have PBX system and a router with 16 FXS port. the PBX connects to router via E1 CAS and fxo-loop-start signal.The PBX guy told me that he has defined 16 extension on E1 link.So I want to hear PBX dail tone on my FXS phones.the sesond issue...
Hi all, I have a E1 connection to the PSTN network, our local city numbering plan is that numbers are 6 digit. The problem is that no body can call us directly to our extensions for ex. 555-555 8888 because analog telephony forwards digits one...
Gurus,On a CME, in a scenario where I have some 7960's in an office setting, but then multiple 7912's in 'common areas', is there an ability in the CME to require the use of a login or PIN on the 7912's in order to make "outside" calls? Internal exte...
