Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hallo, I have tried to reset IP Phone to its default value with the described documents obtained from cisco, but no reset is done and I have the following problem At the Display it is written "CISCO SYSTEMS" Line Buttons are blinking one by one and H...
Whe I try to upgrade the Subscriber to version 5.1.2.3000 the Call Manager is not able to find the parch from the DVD disc, in the Install Upgrade Retrieval Mechanism I select Local, and I insert the DVD with the patch. I recorded the patch with the ...
Hi all,I'm trying to set up a backup router to my primary 7206. The 7206 takes care of everything at the minute so I want to run my VoIP traffic over the 2821. I've got a few different IOS but none of them allow me to put the following commands onto ...
Hi,I have CCM 6.0 with a pub and a sub. I started the backup and on the screen I can see that it backed up all the information from the publisher, however when it started to back up subscriber, it couldn't. It stopped (actually freeze) at 52%. Has an...
Hi,I configured IOS Enhanced conference bridge for CCM 6.0. when I create an ad-hoc conference the ip phone that creates the conference can not be heard yet can not hear other participants . Other participants can hear each other without any issues. ...
Hi,The users I created can not access ccmuser webpages, I get "Invalid User ID or Password" error. I added end users to Standard CCM End users user group which gives CCMuser access to endusers. I also associated the device with the end user, selected...
Hi there ,i would just like to know whether it is advisable to change the cluster ID`s from the default in an already existing Callmanager environment ,if possible what the steps are and what the possible risks are. The environment only has 2 callman...
Hi there,I have an CME 4.1 with IOS 12.4.15T3. I followed the admin guide to implement custom ring tones. I tftp'ed every single file including the ringlist.xml and distinctiveringlist.xml and followed the configuration as mentioned above. Still my 7...
Para Guru,I had configure a acctfixedpin.tcl into my CME boxISO 12.15TCME 4.1my problem is, sometimes it works (ask for pin) sometimes it didn't work (didn't ask for anypin)what might be the problem ? please englighthere is part of the config related...
The Scenario:We are attempting to build an enterprise phone system utilizing one centralized SIP trunk, connected directly to a CM (6.0.1). The remote branches are on IPSEC L2L VPNs, and phones register with CM via SCCP.The Problem:When a branch pho...
I have about 150 7961G phones, about 15 will not upgrade their firmware. Am running CCM 4.02 these phones are1)at a remote site with 512k WAN link2) are the early 7961s we got about 18 months agoI wanted to load latest 8-3-3Sr2 firmware, that failed ...
I have been investigating issues where certain phones traffic is not passing QoS parameters across the LAN. I started walking back through the network and got all the way to the access switch where I did a "show mls qos inter fa XX" and found the fo...
Am I correct that in addition to Unity fax integration steps, the router has to be configured for T.37? So faxes are converted to TIF's on router, and then TIF's sent to Unity?thanks
Have anyone got problem with MMC process in callmanager 4.1(3)sr6? It cause the CPU spike to 100%. Stop callmanager, IIS service did not solve the issue. The task MMC used most of the CPU. After reload the publisher server, the CPU drops to normal le...
hi all. Were going to put in a new CME box, connected to an ISDN 30, replacing our UC520 running over ISDN 2.Internally, we've got 3 companies, in one room.We want company 1 to have number 111111 for example. Company 2 will have 222222And company 3 ...
