Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
we find that pstn vg always switch over the registration to publisher. we don't know what is happening. any command that we can trace?
Hican anyone please help me with the following queries:i am trying to deploy a branch srst setup with a 3845 srst bundled router alongwith 7961 and 7941 phones,the cisco documentation states that only srst 4.0 is compatible with 7961/7941 phones so i...
Hi guys, i am wondering where to change the dscp value that call manager use for sccp. cisco documentation says it should be a setting IpTosCm2Dvce in service parameter. can't find anything like this.can anyone help? the only dscp setting i know is i...
Hi,I was wondering about the conferencing features in CallManager 4.2.What is supported standard? eg. how many 3-way conferences to mobiles would be supported?What benefits features does the conference bridge provide?Thanks in advance
We find that when user who answers a call on a phone that is connected to an FXS port that has Calling Line ID (CLID) enabled for all voice gateways hears an audible squawk for a few seconds. We're using CCM 4.1(3) with voice gateway IOS 12.4(3b). W...
Hello,I'm trying to route the calls made by the extension 18 to a determinated port. For example if the extension 18 dial 0977xxxxx the call have to go to the port 3/1 and the if the extesions 1x dial 0977xxxx have to go to the port 3/0Based on the c...
Hello, I have one digital link configured on a Controller e1, My carrier askme to change ANI digits, to forward calls to PSTNHeres my Conf.controller E1 1/0 framing NO-CRC4 ds0-group 1 timeslots 1-15,17-31 type r2-di...
Hi all,We are in the process of deploying 7921's in retail stores, which requires CME 4.1 or 12.4.11XJ/2/3 or the new 12.4.11XW (CME 4.2).We have been using the Cisco B-ACD Tcl scripts with CME 4.0 without any issue for a while now, the only change h...
If you have a partial PRI coming into a gateway from the telco how should you configure the pri-group? For example I know that with a full PRI using MGCP you would use the command:pri-group timeslots 1-24 service mgcpOn one of my gateways this comm...
If a call comes into IPCC on a 1-800 number, and the call gets routed to a particular agent, how do we retrieve through JTAPI the original called number? Is this info available?
I have the following problem:- When the operator of the company dial a external number (it receive the ringback tone) and it receive a incoming call (and answer), the first call (outgoing call - in state ring out) is finished.My CallManager server is...
Currently: One cluster with 7825 (pub) and 7825 (sub).Target: One cluster with DL-380(pub) and 7825 (1st sub) and 7825 (2nd sub).This would ordinarily be straightforward, but I need to give the new Publisher a new name and new IP. If I build the new...
Hello,I've got a CME router IOS 12.4(9T) running as a SIP-UA into a service providers SIP network. I was running 12.4(8a) and the registrar timers was fine. Every 25 seconds or so it would renew my registration.I changed to 12.4(9T) because I needed ...
hii want to connect to a voip provider i have 7815 MCS and 2811 router with 1 M internet connection speed i want to add a SIP trunk link to this provider assume their target IP is 194.22.3.1 and udp port 5060 what steps do i need to configure this on...
can ATA186 supports call pickup? if yes, how to configuer?
