Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
aHow does Skype for business work, we have some partners that we would like to talk to with Skype for business. Today we have following setup- Cisco Spark Room Kit - Office 365 with Skype for business- WebEx account The WebEx works fine, but can't...
Hello, I have CUCM 7.1. I'd like use it TFTP server for config files SIP phone "Aastra". Aastra need filles *.cfg (aastra.cfg, etc), but when I upload this files to TFTP Server CUCM and I reboot Server for apply the changes, I can't find files *.cf...
Hello All, In our lab we had 20 have number of Cisco 7960G IP Phones. Some 9 of them are facing ‘tftp file not found’ issue. First of all, can anyone explain what could cause this? I have checked firmware version for the operational ones and this is ...
Hello all, I'm currently working on a project to upgrade CUCM from 9 to 11. It turned in to a migration project instead of an upgrade because we wanted to put CUCM 11 in new address space. I currently have the migration done, so CUCM 9 is still in ...
Hello All, One of the user has two extensions associated.1011- own extension1012 - general/shared extension On extension 1011, calls are forwarded to the user's mobile handset number.Is it possible to do the same with the shared extension? Meaning,...
I have a new CenturyLink SIP Service. CenturyLink said it is new and doesn't match the Cisco guides. In short in CUBE they want me to send calls to their network as; SIP Signaling IP X.X.156.245:5060 RTP IP X.X.156.244 I'm just drawing a blank o...
good day! i am currently setting up IP PHONE in my network and i am new to this. i have cisco 2921 router and IP phone 7841. currently my router does not have support for 7841 and i find it difficult to load firmware(loads file) for the said phone....
Hi All,We have SIP trunk for our PSTN connctivity with CUBE and CUCM 8.6 Below is the setupService Provider-------SIP------>CUBE(2911)--------H323----->CUCMCUBE is running IOS Version 15.2(4)M3. Problem is When we do internal (IP Phone to IP Phone) ...
Hi I have 4 phones that are running SCCP VERSION BOOT ID PC0303010001, APP LOAD ID P00308000900 I need to upgrade these to work with another sip provider and although I have downloaded the files I think I need the phone reports that it cannot fi...
Hello... I recently acquired three ATA190 for analog phones I still have. I am trying to configure one of them and some of the issues I have found are: - CUCM is rejecting it to register. I know this is a topic that is on the topics, but I want to re...
I have a 2911 with an FXO port. I see this in Callmanager/devices/gateways. I see where to point an incoming call (Attendant DN). But I do not see or understand, how do I configure to dial the FXO port for outgoing from Callmanager? Is this possible...
Hi All Can I export configuration using BAT from cucm 8.5 and import this data to cucm 11.5? TIACristian
How to install devicepack for cme 8.6 using CLI. I am getting info about gui installation but in my gui there is no option for install/upgrade. Router#sh flash: -#- --length-- -----date/time------ path1 59803980 Feb 22 1907 17:31:44 +00:00 c280...
Hello, We are looking at utilizing RedSky only for e911 mainly because our phones are mounted and no concern of phone movement. I have a question regarding call back from the PSAP to the origination of the 911 call in case of a hangup. Is it possi...
Hi, can anyone confirm if there is any option for headset with 3905? is bluetooth supported? or will the handset jack work for wired headset or some bluetooth enabled headset? thanks in advance.
