I'm new to collaboration and have some basic deployment experience with Cisco Telepresence units. Recently, I've started working with Cisco IP Phones and CUCM. I've been able to register phones, create partitions, CSS, and calls are taking place inte...
Forum Posts
Resolved! Copy existing wallpaper from Cisco 8851
Is it possible to copy the Wallpaper from a phone to upload to CUCM for use with other phones? I have a phone with an older SIP image that has a wallpaper in the phone (not from tftp) the rest of the phones have a newer SIP image and I would like to ...
Hi Guys, I have a problem. When the intallation of CUCM finish an error occurr. I have the dump file, but I can´t to open :( Please, help. TIA Cristian
Resolved! Cisco CUBE multi sip trunks
Hey,I was wondering if its possible (and how) you connect a Cisco Cube to multiple sip trunks (different providers).I have 3 sip providers one in Australia, one in the US and one in the UK, but I havent been able to find any descriptions how you do t...
Resolved! CUBE for multiple SIP trunking
Hi Expertscan i a use common CUBE infra for multiple customer SIP trunking requirements. For eg i want to deploy only a single CUBE router on my side with different loopbacks which in turn connect to different customer CUBE devices
One of our client had weird issue. External call received to multiple Cisco phones at same time. The weird part is external call is same number . Calling party: Same number Called Party: Multiple Cisco Phones ( All phones configured with different nu...
Resolved! 2nd KEM for 8851
I'm planning to add 2nd KEM to Cisco 8851. When i plug the card in it's not getting any power. I'm provide POE and check the on the switch it provide 30 watts. I even try to used External power both way it power the 1st one but not the 2nd one. Am i ...
ASA-SSM-AIP-20-K9 With ASA 5540 supported , Hardware: ASA5540, 1024 MB RAM, CPU Pentium 4 2000 MHz Internal ATA Compact Flash, 256MB BIOS Flash M50FW080 @ 0xffe00000, 1024KB current signature version S947 ....
All, We have a requirement to block 1 nuisance caller for only 1 CUCM endpoint. All of the documentation I have seen points towards blocking in IOS or in CUCM with the Route Next Hop feature which seem to block nuisance calls for ALL endpoints, not j...
Hi, We experience a problem with a SIP trunk between CUCM (6.0 and 8.0 <- Customers) and a Huawei SoftX3000 (Provider).The problem is that the Call Manager (6 & 8) does'nt accept calls from Huawei.The problem appears even if we use a voice gateway us...
Hello, I follow the link to rebuild my pub-cucm. https://www.cisco.com/c/en/us/support/docs/unified-communications/unified-communications-manager-callmanager/116946-technote-product-00.html#anc3 ----- step1. utils dbreplication stop >> To stop DB syn...
Hi there, We're running CUCM with NTP pointing to an old (removed) domain controller. I'd like to edit CUCM's IP server address but I don't seem to be getting the syntax correct. I've been reading I should be able to type "utils ntp server add x.x....
we use JTAPI to monitor status of Phones(registered/unregistered). It works fine for Cisco devices, but we also have to monitor other devices(E.g. AXIS door monitor) which is registered at CUCM. JTAPI seems to not support it. How can this be achieved...
Hello,I have a CUCM 7.1(3) system and have a requirement to give serveral users remote destination profiles. I noticed that there is a BAT workbook tab to bulk in RDPs but in CUCM when I go to create a RDP BAT template it specifically requests for t...
Wanting to setup some call blind transfers for my agents. Seems call control has been removed in 10.5 from the interface. Anyone know of a good way of doing this in 10.5? Some background; this is on a new server, we are upgrading from 8.6 to 10.5. ...
