Hi !I need to create some statistics about login/logout on IP Telephones in a Call Manager 3.2 solution. Is it possible to read date/hour login and logout insomewhere ? Are these information stored ? How could I read them ?Thank you very much,Luca
Hi !I need to create some statistics about login/logout on IP Telephones in a Call Manager 3.2 solution. Is it possible to read date/hour login and logout insomewhere ? Are these information stored ? How could I read them ?Thank you very much,Luca
Hi all, I upgraded the attenedant console to Console version: 1.1(3) with the Server version also being 1.1(3)Since the upgrade we do not get the users names calling coming up on the screen of the attendant console. The phone still shows the name.Is ...
Hi, EverybodyDuring a call party bettween an analogic phone connected to an ATA or an ip phone the user doesn't receive any signal/sound (like an busy signal that PBX phones do) that the conversation ended.Thanks in advanceMP
Hello,I'm configuring user device profiles for Extension mobility on CM 3.3.2.I can log in and off on a phone, but phone is rebooting immediately after.I saw on this forum that it was due to the fact that the button templates were different on the pr...
Hello everyone:I have a 1751 configured with 2 dial-peers voip to send calls to 2 CallManagers. I followed this document to configure CCM 3.x redundancy http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a00800948...
I am building a test Call Manager.I have a test AD domain however it is Cornerstone.IT.A dot IT instead of dot COMI go to add the plug-inI put in my hostname: NY71.Cornerstone.IT (I also tried just using the IP)default port port: 389DN= cn=Administra...
Hi,How i have to configure the ip softphone 1.3.3 and the callmanager 3.2.2c, if the softphone should control the ip phone 7960?The softphone should not work as a standalone.Best regardsHilde
1) hub and spoke topology. DS3's at hub site. Multiple T1's at spoke sites. 2) spoke sites may have anywhere from 10 to 200 telephones, and 20 to several hundred data ports. 3) the requirement is 4 FXO for local PSTN access / failover plus one port ...
I'm looking to replace a Dialogic D/41D card in a working Unity system with a PCI card. Would the Dialogic D/41EPCI be the appropriate PCI counterpart?
Does anyone know of some type of freeware SMDI enabled voicemail system that I can download. We are going to purchase the Unity in the near future but I need something to get me by until then.
I have a AS5300 connected to PSTN with ISDN PRI and a Cisco2600 at the remote site, also with PRI to PSTN.When incoming call from the PSTN to 5300 it came with # at the end of the number. (358123456#) and then match a dial-peer on the 2600 that get ...
My customer's Unity imported some Exchange 2000 users that did not have first names in their profile. These users cannot be accessed or deleted in Unity, nor can they be reimported. My understanding is that these should not have imported, however t...
I cannot find any documentation for this upgrade. How can I upgrade or not allowed ?Thanks,
I try to run icsconfig on ics7750, all modules dectected except the SPE310 that runs the system software ( below output ). This spe310 on slot 6 is CCM. The CCM is working fine. It processes calls normal but can't be dectected by icsconfig. Has a...
Has anyone had any experience using a USB sound device as a MOH audio source on the ICS7750 and will Cisco support this type of configuration?Steve H.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-27-2024 02:35 PM | ||
09-24-2024 05:35 AM | ||
09-19-2024 05:56 AM | ||
08-23-2024 11:56 PM | ||
08-21-2024 05:48 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |