Other Network Architecture Subjects

I have two LAN with 1000 meter cable Category 3 between them.I use in one side 1 cisco 2611 connect to 1 catalyst 2950 LRE and in other side 1 CPE 585 connect to 1 cisco 2611.When i make ping from router 2611 in one side or from PC to the other side...

i have to design a network with this layout... ```````````serverfarmswitch - coreswitch - edgeswitch `server/``````````|```````````````````|```````````````````|`````````\ serverfarmswitch - coreswitch - edgeswitchIt's supposed to show dual link...

I would like to be able to determine what User is connected to what Switch port, using the ARP table. Is there anyway to do this using a tool or Scripts (other than ciscoworks). Currently I have to go to our Routers ARP table to get the Users Mac ad...

Recentlly,I find error message in my Cat2948 switch,The topo is:CBX500(Lucent switch) connect to port 2/1 of Cat2948,another switch connect to port 2/5 of cat2948,and few hosts connect to other cat2948 ports.Many times,I found error message which sai...

Hi I am experiencing output drops on my ATM. The load is around 50 %. Any suggestion why this occur?Output from a show interface ATM 2/0ATM2/0 is up, line protocol is up Hardware is ENHANCED ATM PA MTU 4470 bytes, sub MTU 4470, BW 7000 Kbit, DLY 80...

As a Multilink bundle is being built up it appears physical interfaces(out of the dialer-pool)are selected sequentially to dial out on basedon the physical port number with the highest used first eg. 1/3 then1/2 etc.When I have a faulty ISDN link tha...

Hi all, Can any one help me to configure Load balancing on 2620 for my 2X 2Mbit serial lines.Any commands/ Doc's appreciated.ThanksAbdul

Probably more of a router issue.....We have seen serious router problems due to the use of Insight Manager. Its discovery process, scanning a wide range of ip's, causes the ARP INPUT counter in SHOW PROC CPU to rise high, slowing down the router. The...

I have a Cisco 1900 Switch that has 7 of it's ports connected to seperate small networks. It's trunk port (A) is connected to a Cisco 2611 router. The switch is configured for seperate VLANs and so is the router. When I show the running config on the...

We hae multicast enabled on our Network./ We have 2 Cisco 6509 with MSFc and have it enabled globaly and per vlan participating in multicastingWe want to start usng Ghost Server and want to use multicast. I have enabled multicast in the vlan and when...

Hi.. All,Using Cisco 2590 Switch (Dedicated to below mentioned DMZ)Setup = Checkpoint Firewall NG with Stonebeat Cluster.I am finding something strange problem in one of My DMZ where I used all the legal IP address block. I use my proxy servers and ...

Hello ,Is there a 10 Base-FL module for 6509 /4507 ?. Currently , we have a shared Network for our Automation Network , planning to upgrade to Switched Network based on 6509 platform. Most of the Automation systems have Thicknet Interface (10Base-5 ...

We have two routers with ISDN PR1 to receive the ISDN call. The remote router tries to dial to the 1st ISDN router and retry 5 times. This is to make sure all the ISDN channels connect to the 1st ISDN router. If all the attempts to the 1st ISDN route...

Hi all, I am just wondering how to configure an ACL for the only VLAN on my switch.And I have no ACL on my 2620 router. We have an outsourced dept which should only access a Billing S/W in our network.And this VLAN is created for this dept.Could...