Routing

Can I connect 7206 and 3900 series routers through Fiber?

We are migrating from a Microwave T1 WAN to a Fiber ring WAN which I'll be connecting to our providers Ciena Metro E switches. Eventually we are going to move away from the routers, but the network is a little too complex as well as spanned across ...

cannot ping across subinterface on non-native vlan

I have R1 connected to R2 with a direct ethernet connection. R1 has is using a subinterface and R2 is not. If I use this config I do not get reachability:R1int f0/0no shutint f0/0.12encapsulation dot1q 12ip add 192.168.1.1 255.255.255.0R2int f0/0ip a...

migrating router config from 3725 to 3945e

I'm new to cisco & this forum so please any help would be appreciated.I'm trying to migrate the running-config from our old 3725 router to our new 3945e router. Almost all of the config is copied over except for a few lines that come up as unrecongn...

Max interfaces with pim

Hi everyone,Could you please tell me on 3750X how many interfaces can be configured with PIM activated on ?Best regards

What is cisco cutting-edge technology

Where the future lies..!! want to learn some new technology for a change.. :-)I have been working on Data and security for years and want to learn something new and intresting.. any thought ?thanksAmar

Resolved! Tunnel Interface

Hi,Any one will explain brief about the following tunnel interface conf.interface Tunnel0 bandwidth 6144ip address XX.XX.XX.XX XX.XX.XX.XXip mtu 1514ip load-sharing per-packetdelay 3keepalive 3 3tunnel source XX.XX.XX.XXtunnel des...

Cisco Switching Series Software

Dear Expert,What is differece between of them?LAN Life:?LAN Base:?IP Base:?IP Service:?please kindly detail of them. Looking forward to get your feedback.Thanks,Siren

Resolved! Single rate,dual bucket policer

Hi.I have next config:police cir 80000 bc 10000 be 5000 conform-action transmit exceed-action transmit violate-action dropAccording to this Bc bucket refill 10000 tokens each second meaning 80kbps throughput. But what if I set:police cir 80000 bc 700...

Netflow v9 and NSEL capturing

I need to capture Netflow v9 and NSEL traffic. Ergo IOS netflow traffic, and ASA netflow traffic (NSEL). I am trying various netflow caputiring tools right now, but they are paid for offerings that do far more than what I am really looking to do. I s...

Resolved! IP SLA fine tuning

Hello AllI have two routers connected using two links on different service providers and they act as a back up to one another. I have IP SLA running to between them to failover. I would however want the failover to NOT being instantaneous and would l...

NAT device

we have A wireless link (pre-wimax) that provide me with 2 Mb internet connection (tagged Ethernet frames) and we have 6 real IP what i need now is what is the best and cheapest device to do NAT and DHCP to allow users to access the internet , i am t...

QoS for IPSEC(port 500,4500)

hello,please you have any idea how can I configure QoS in the router CISCO1841 for the port IPSEC(UDP 500 ,UDP 4500) and the port tcp 4433 thx for your help

C3750x trunk to HP C7000

Hello,We install a stack of C3750x switches rescently. A HP C7000 blade server uplink to C3750x using etherchannel and 802.1Q.If the trunk includes a RSPAN vlan on it by 802.1q default configuration, the VM on HP blade cannot ping the same vlan serve...

Advice - 7200VXR with multiple full BGP routing tables

I have a c7204VXR NPE-G1 1GB RAM 6 GigE (3 on the NP, 1 on the I/O, and 2 PA-GE). Passing about 150Mbps of traffic. It's taking a full eBGP feed (470k routes), and connected to a peering fabric (30k routes so far).When I turned up the peering fa...

How to config edge network to send traffic to two ISP connections that are different speeds

I have a client that currently has two 100 meg connections to the Internet from the same provider. They are going to upgrade one to a 500 meg connection soon and it will be from a different provider. Their edge routers are connected to the provide...