My RV134W will frequently lose internet connectivity. It does not matter if I use a wired or wireless connectionI see the following messages in the logs every few seconds.Alert dhcpc: DHCPC: send discover!!!I don’t know if this message is rel...
HiI am currently experiencing issues on the ISR 4321 Version 17.3.5 whereby the tunnel hangs and I need to reset it for packets to start transmitting.I have experiencing this issue on two devices already.Regards,Salom
Hello good night, I am having the following problem, I have a router 2811 in my personal lab and I am trying to put this router connected directly to the isp and my connected machines in 2811.
ISP —> ROUTER 2811 —> PC
Well Router 2811 has port 0/0 co...
i completed my certification through pearson vue and got the report card as well.. now i am unable to find my certificate on cisco. i tried certification tracker but in 1st option i never received any mail on the entered mail id. In 2nd option i am u...
Situation:I'm upgrading a part of our network. They are sites connected by radio links.We also provide them with cellular (4G) connections for backup when the radio links go down or are being worked on. Sites use a mix of 897, 829 and 1113 model rout...
A question;How can i loadshare outbound upstream traffic in a bgp multihomed sitiuation whereas iam peering with 2 diffrent AS's.Iam only receiving a default-route from my upstream peers.
Hello all,
I am having a bit of an issue with trying to get an ASA 5525 to form a neighborship with a Nexus 9504. They can see and communicate with each other via layer2 VLAN connection.
Trying to figure out what I am doing wrong. Here is stippets of...
I am trying to configure access from DMZ at one location to the DMZ at another location. I have a ASA5508 at location 1 and at location 2 we have an ISR C2900 that has our BGP configuration and a ASA5516 where the DMZ is configured. The office traffi...
Hi!I'm wondering if it is possible to replace my current modem (EPC 3010) from the ISP with a 2951 router.The modem is recieving connection through a coax cable for which I have purchased a coax F to RJ45 converter (https://www.amazon.de/dp/B07ZFZ1KN...
Hi everyone, let me tell you a little about my network and the issue I'm having. I have a Cisco 1921/K9 connected to the Gigabit FTTH from my ISP. From 1921/K9, I have a 2960CG with 2 trunk and 8 access ports. In the acces ports, I have an AP (Cisco ...
Hi,I have a router with two links. One is BGP link and another is Static Route. I want to configure both ink as failover, where static route will be primary and if static route failed it should shift to BGP link. Once static route up again it shoud
Hi All,
I need help on below.
1) What is equal of Juniper MX series router's Routing Instance and logical system in Cisco ASR and how to configure the same.
2) Can we have multiple next-hop with tracking in Route-map for PBR.
Thanks,
AKK
Dear All,I have One ISR 4331, Which was managed by Another IT Guy, Unfortunately he left without proper Handover. Well, Coming to the point, I created one DHCP Pool on ISR 4331 /23 Network. I'm Getting an IP address but internet is working. DHCP Pool...
Hello, I'm trying to understand a routing configuration we have on a core switch.The default route to 0.0.0.0 with "next-hop1" is a BGP one, and we also have specific ones in BGP as well. A static floating route has been added with "next-hop2", with ...
i try to make vpn l2tp on cisco the connection is so good and it is login on my laptop but on i try to ping this interface GigabitEthernet0/0/1 my ping is timeout Current configuration : 2685 bytes!! Last configuration change at 00:12:15 AST Wed Ju...
