Dears, We set up a MW P2P link between branch and HQ to get internet from HQ and it's working fine as per the topology attached. My branch devices and Pcs are configured with IPs from subnet: 192.168.99.0/24 GW: 192.168.99.1 and all within vlan 1. so...
Forum Posts
Resolved! EHWIC 4ESG
Quick question, how do I configure this 4-port gig expansion card on my Cisco ISR 1921 for vlan traffic? Compared to the two normal interfaces where I can just do g0/1.1 or g0/1.2 etc... then bam you got it going.
I have an ASR1001HX that has the correct code on bootflash:, but there is an image I put on this device for an ASR (asr1001x-universalk9.03.13.05.S.154-3.S5-ext.SPA.bin ) before I remembered/realized it was an HX. So it keeps trying to load that when...
I have a AP connected to a port on my switch which has the the "access-session host-mode multi-domain" configuration item. I want to change that line to "access-session host-mode single-host". Can I change the mode in flight or should I shut the port...
Hi, I have some ASR901's in Solarwinds that are showing high discards for this interface "ToP0/12-To0/12".I'm not sure what this interface is or how to troubleshoot it. Unless im just being ignorant and looking at it wrong? Thanks for any help.
Does the Ingress Interface for ITD need to be be a routable interface with a VIP or can I simply declare it as a particular VLAN that's defined on the switch with no interface? For more clarity, I have a Nexus device that is sitting inline at a gatew...
Hello... Looking for some insight/help on my config. I have a NAT setup as a NetworkObject, so there is no STATIC route from inside to outside... How do I setup a second NAT NetworkObject and the associated SLA/Monitoring, that I would need to priori...
Hi All.I have a C1111-8PLTEEA running Version 16.10.1b. It doesn't seem to have any info on the LTE modem. When I issue 'show cellular 0/2/0 hardware' i get this output:Modem Firmware Version = Device Model ID = Package Identifier ID = International ...
Resolved! ISR 4331 - Max throughput licence
Hi, sorry for this simple question but I cannot find what is the MAX throughput licence you can buy for ISR4331.I have found info that 4431 is maxed at 500Mbit/s and 4331 is maxed at 300Mbit/s, is this correct ? show platform hardware throughput leve...
Hello Dears,We had an access issue to a specific router when i consoled to it i found. 1-The SSH was disabled automatically 2-There is an IPSec tunnel created to a remote router. -What might causes the SSH to suddenly become disabled? -if i generate ...
Resolved! Route Map with IOS-XE Guestshell
Hello. I'm trying to use a route map to designate an egress interface/next hop IP for iperf traffic from one branch router's Guestshell to another. I applied the route map to the virtualportgroup 0 interface but traffic from the Guestshell traffic do...
Resolved! Cisco ASA - Can't get through NAT
Hi. I have cisco ASA with 4 vlans (DMZ, inside, outside, WiFi - unused). I have also NextCloud server in my DMZ vlan which i want to be accessible from outside. I managed that on Cisco Router but i'm fresh with Cisco ASA. I tried to do it how officia...
Hello,I have a router which is currently setup for TACACS authentication & it's all good for the VTY lines. What I would like to do is have the console port use a local username defined as test rather than tacacs. I've set it up with the following ho...
Might someone be able to help explain the difference between the following global configuration mode "domain" commands their effects: domain [domain name] vs. ip domain name [domain name] Below is some example output of what I am seeing on two dif...
Hi, does anybody know how to resolve the issues regarding IR829 not booting.I have write erased config on one of my routers, now router is not booting it cylcles like this over and over.IR829 Loader Stage 1 Version 1.23 FPGA version 0x20b00 built 20...
