Welcome to the Cisco Community Ask Me Anything EventWe invite you to participate in our upcoming Ask Me Anything (AMA) conversation. Please submit your questions from Thursday, April 23, 2026, through Thursday, May 7, 2026. Our experts Eris Bleta, Mo...
Forum Posts
This is just a "sanity check" kind of question.Customer has two different Meraki Orgs (and thats the way its gonna be).The should both access the same resources in Azure.Customer has already setup one vMX for Org1 in Azure, works fine.Can we just set...
Hey I have a Cisco ASA that connects to the same remote entity via two different firewalls using route-based VPN tunnels.I need failover built in from my side, so if the primary tunnel fails, I send traffic over the secondary tunnel (the reply traffi...
Hello everyone i want to make ACL for CoPP but i have a doubt witch have to make it.ip access-list extended ACL-CoPP-IPsecpermit udp any eq isakmp any eq isakmppermit udp any any eq non500-isakmppermit udp any eq non500-isakmp anyorip access-list ext...
IGMPv3 Max Response Code field uses an algorithm allowing values up to 52 minutes, but NXOS syntax limits the customer to 25 seconds. If a customer sets the command to 25, how is this number specified in the field in binary? Does it insert the number...
Hello Everyone,We are having one issue with HSRP pair IE4K switches and ASA 5525 firewall in Cluster pair.The setup is attached file. Its basically a triangle with ASA firewall at the centre with 2 legs to the switches. The switches connect to each a...
Resolved! Using SD-WAN 20.15.1 in CML 2.8
Dear All,I need your help to understand something. When I ran the automated script to install SD-WAN in CML 2.8, everything works as expected (https://github.com/cisco-open/sdwan-lab-deployment-tool/).When I decide to install manually each components...
Resolved! Cisco Voice and data router
HiI need a Cisco router for integrated data and voice. Which model would you recommend, and what are its requirements?Regards
Resolved! MX and Zscaler integration
Hello, I’m not an expert in Zscaler solutions, but I know that MX supports integration with ZIA. What about ZPA and ZDA? Does anyone have experience with those?
Hi All,I needed some help i am creating vrf in C9300LM-48T whos running software version 17.15.03 and gives me errror of " % Feature is not supported " below result for referrence.If someone can help me to understand if its a licensing issue or firm...
Resolved! OMP to BGP Redist Question
Dear Community.I have an OMP into BGP redist question that is sort of perpelxing me.Scenario: CEDGE1 has an eBGP neighbor that it is learning the prefix 10.18.17.0/24 from. However, the CEDGE is also learning this same prefix via OMP. OMP is configur...
I'm a noob at networking and I got this impression with this task which seems pretty simple but I couldn't have it!!A topology with overlapping subnet and required internet connectivity causing me so much trouble from yesterday. I know it can be solv...
Hi we are facing a memory issue and the bootflash: is totally full. Therefore the ISR4331 running on version 16.12.6 is rebooting in a loop. From rommon I'm not able to clean flash: as there isn't any commany "del" "delete" "erase" "format" or even ...
I just did an experiment with using BGP over IPSec to Amazon AWS with MX 19.2.3.https://documentation.meraki.com/MX/Site-to-site_VPN/BGP_routing_over_IPsec_VPNAnd it now works (never used to)! I have stood up two tunnels to an Amazon AWS VPN gateway...
Attended an interview today for a Network Engineer role.This is a problem that every network engineer might have faced, but it's rarely discussed.I prepared for topics like, OSPFVLANSTPACLthis is basically what i learned in my CCNA and Many new engin...
Hi AllI have set up a MG51 cellular gateway, this plugs into the WAN1 on my MX68 device and provides the MX with a dhcp IP.I added a fixed IP assignment and port forwarding so it forwards VPN traffic to the MX, however I have noticed my MX didnt take...
