We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hi,How can I check Warranty details of Cisco Devices.
Hi,I have a Cisco SG300-28PP. I am trying to configure vlan. I added vlan30 in vlan settings. and also made port 14 as trunk port and add vlan 30 as tagged member. but still it is not giving vlan ip to connected device. untagged ip is getting. issue ...
Hey all, I have many CBS-350 series switches. I am running two commands on all devices, and I need to automate it. on each switch run "show vlan" and "show cdp nei detail" and get the output saved on my device. is it possible to do somehow? please he...
Hi, Cisco.Please help me check the warranty start and end dates for the serial numbers below.SFDO27430SEWSFDO27430N21Thank you
I have two Cisco SG300 Switch. And create Vlan108 both of them.Switch 1 Ip: 172.16.10.5Switch 2 Ip: 172.16.10.79Switch2 GE19 Connect to Switch1 GE27Switch1 GE27 config is:Interface Mode Administrative VLANs Operational VLANsGE27 ...
I am able to retrieve PoE data via the CLI and the web interface, but I am unable to find these data in any of the MIBs.please advise.thanks,James.cbs220#sh pow i cPower management mode: Port limit modeLegacy device supports: disabledUnit Power Statu...
Hello guys,i bought a Cisco SG 350-10 switch privately a while ago. Only later did I see that there was no power supply included. Unfortunately I can no longer return the device. Can someone tell me which power supply I need for this switch ? On the ...
Resolved! cisco 220 24p - Illegal software format
i'm try to update software for switch 220 24p had old version to latest version, but always has same message (Illegal software format) .. any help !!
I am trying to:create ACL for each server and configure NAT for the ACL where I map private IP addresses to public IPs. Which command can I use to achieve that in CLI for a CBS 350 series ME-switch
Hi everyone, I have inherited an existing 2 host setup and have been troubleshooting the network performance since I arrived. I have noticed that not all the VLANs in use by the VMs have been assigned to the LAG group connecting the ESXi hosts to the...
I have a cisco cbs 350 10 port poe switch. CBS-8P-2GI have a cisco cbs 350 28 port fiber switch. CBS-24S-4GI have port 9 and 10 on the smaller switch in LAG.I have the bigger switch in LAG on port 26 and 28.I can't seem to get it to work. Any help wo...
Curious to know if others are using "qos basic" or "qos advanced" to support voip (Deskphones using voice vlan).I'm trying to see if I can get by with just "qos basic" and "priority-queue out num-of-queues 3" so as to not overly complicate things in ...
hi there...I have a Cisco 110-16-PP SMB switch. I have a cable connecting my Xfinity modem/router to a non-POE port on this switch. The left LED light on this port is flashing Amber, and the right LED light is solid green. This suggests a network l...
Hi,I have a SG350-10P switch running the last 2.5.5.47 firmware.The switch is set to factory defaults. Has yet to be programmed.I noticed that my access points didn't get any power. Checked with an external PoE adapter, AP working fine. Just not with...
