Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
I have a server that has teamed network cards. This is connected by two straight through cables to a Cisco 2960G. The two ports are not aggregated or teamed.What is the impact of this configuration to my network?
I Have 5 building with 3 IDF in each building, the client access range from 100 port to 200 ports 2950 or 2960 with 1 gig uplinks to 3560-g's. my core is two 6500sup720-3b. the bulk of my users are in 3 of the build with about 200 is my largest stack...
Hi All,Abit of a open question really but am really afer abit of advise,Currently we have a flat network 172.16.x.x 255.255.0.0 without any VLAN's, we are now looking to introduce VLAN's into the network using a /24 mask 172.16.10.x 255.255.255.x etc...
Resolved! Multi-region MSTP
I am confused about single vs mult-region MST. I know that in single region, the IST root is elected by the lowest bridge priority. But in multi-region, there is also an additional root bridge election (regional root) with lowest cost path to the C...
Resolved! Cisco PIX Crude Traffic Load Balance
Hi all,Im looking at performing a type of crude load balancing from a single Cisco PIX. I have a scenario whereby I have two ADSL routers directly connected to two seperate external interfaces on the Cisco PIX. I am aware that the device does not s...
Resolved! C2960-LANBASEK9-M image on 2960 switch
We are using the C2960-LANBASEK9-M image on 2960 switch. As I understand, this is just a layer 2 switch and therefore should not block traffic by default for example udp broadcast and unicast traffic. Am I right in thinking this. Also can somethi...
Hello,I have two switches(6509 and 2950) in my network which have same vtp domain name. They are not directly connected via a trunk and so they did not exchange VTP updates all this time. However I need to change the vtp domain on 6509, so that I can...
We have 2 x 2960s series 10G and 1 x 2960s POE+ series 10G in a stack connected with two 10G connections to two core switches and I’ve come in this morning to find that i can’t ping the stack at all. So i tried to console into the stack and still no ...
My device-880 routerDesign - I want the L2 ports in the 880 router to allow only 2 mac addresses,one voice one dataConfiguration- I am statically assigning mac addresses to the portslike thisSw(config)#mac-address-table static 4.4.4 interface fastEth...
Hi Team, We are using MPLS VPN connectivity for inter branch communication. We have chosen Hub & spoke connectivity from MPLS service provider due to cost constrains. Now few of our branches need to communicate each other via HUB router. BGP is the r...
Hello,Just a quick question as i did not find any document related to this function on fwsm, is wccp supported on the fwsm and if yes since which version ?My versionFWSM: 4.1(3)ASDM: 6.2(2)FThanks in advance.Regards,
HiI have a Cisco 877 router and wish to know how I configure the LAN ports for different IPSec tunnels. Thank you for your assistance.Regards
Resolved! MST and Layer3 Design
Above config is fine using PVST/RPVST STP.For MST, if I put all VLAN2, 3 and 10 to instance 0 only, MST-STP merge to one such that the Layer 3 design does not work. Any method to make MST work in layer 3 design using instance 0 only?
Hi,Can anybody advise whether it is possible to create a VSS pair using CWDM.The scenario is 2 Data Centres with 2 Dark Fibres between them. Each DC has a 6509 capable of VSS. A CWDM-MUX8A and EWDM-MUX8 for 10GB connectivity would be installed at eac...
Resolved! Advertising Static Routes
Hello,Our EIGRP network will soon be connected to a 3rd party network which we have no control over. The 3rd Party are refusing to take part in any dynamic routing but have hundreds of non-contigous subnets which we must route using static routes. To...
