I'm looking for a portal to be able to search Cisco equipment by serial number (similar to what Dell has).Example, I submit a serial number into the search portal and a page pops up with S/N, Model, Warranty Data... is displayed. Is there anything li...
Have a question in regards to setting this to 9216 instead of the default 1500:class type network-qos c-8q-nq1mtu 1500class type network-qos c-8q-nq2mtu 9216class type network-qos c-8q-nq3mtu 1500class type network-qos c-8q-nq4mtu 1500class type netw...
Hello all,We can of course use IP SLA's and Track objects to track reachability of a next-hop (like an ISP) and then remove a route to affect our routing, but I'm trying to think of an actual use-case where I would actually do this, as opposed to jus...
Hello,I'm looking for the ProShapes Art elevations for the CW9800H2 and CW9800M wireless controllers. I don't see these in any of the Visio Stencils listed. Does anyone have a place where these are available?Thanks!Ark
Ok so first of all pardon my English, bcz its not my 1st language, 2nd sorry for being noob in this matter, while asking basic things.so I m trying to provisioning my 7942 on sip wo work with 3cx, according to their guide they support 7941, but i thi...
Hello, I have a FTD 1010 in my home lab that's using 1 routed interface for outside and the rest of the interfaces are used as switchports on a VLAN that I use for the Inside. Now I also have a Synology NAS with two interfaces that can be bond toge...
So I tried to upgrade from isr4400-universalk9.17.12.04b.SPA.bin to isr4400-universalk9.17.12.05a.SPA.bin. After the upgrade it will not register with my SIP provider. I see this. Aug 11 02:08:22.843: %SIP-3-REG_INTERNAL: Registration failed. Tenant=...
Dear Community,I’m facing an issue with a single-TLOC Cisco SD-WAN branch (Catalyst 8200/8300 on IOS XE 17.15.03, vManage 20.15.03) where the WAN Edge fails to establish BFD Tunnels with other sites even though it can reach the Cisco-hosted Controlle...
Hello,I have a Cisco AP9130AXE currently running in lightweight mode and I want to connect it to a Cisco switch.I don’t have a controller and would like to make the AP fully standalone. I need the following: The correct k9w7 standalone image for t...
Hi there, currently i'm going to use xrv9000 in the eve-ng but during the loading the ios router requires to enter default username and password. I have tried: 1. root - admin 2. root - cisco123 3. cisco - cisco 4. lab -lab 5. root - root (also tr...
Explore host grouping in SNA to segment networks, set behavior baselines, and boost monitoring. Learn performance tuning strategies to optimize Cisco Secure Network Analytics for stronger security and operational excellence.
Hi,I've been doing BGP multipath labs and it seem that step 8, lowest IGP metric to the next hop, is skipped when you are using multipath eibgp.For example, R8 (below) has two neighbours - 9.9.9.9 which is iBGP, and 11.11.11.11 is eBGP:R8#sh run | s ...
We are trying to make auth work in Grafana via Cisco ISE and RADIUS protocol through OAuth, and we have managed to get this working by using Cisco AV-Pair dictionary attributes. In order to granularly authorize access to differnt dashboards, I need o...
After upgrading several corporate laptops from Windows 10 to Windows 11, the IT team begins to notice that many devices are being blocked by the Cisco Identity Services Engine (ISE) during network authentication. Upon investigation, they discover tha...
in cisco ISE wire posturing, how to achieve below use-case; endpoint windows laptop is connected to switch port 4. If the endpoint is moved to another switch port access should be blocked.
