Activity in Technology and Support
Cisco MTR room AP navigation board stop reacting and freezing
While using MTR the TAP navigation board stop reacting and freeze, on cisco side there's no issue on the logs and in fact the TAP cisco interface still's working but the microsoft interface stop responding.Someone had the same issue
SSH Restriction using object-group under Access-list
I want to restrict SSH to a certain subnetexample: Source Subnet: 192.168.X.X/24Object-Group network SSH_USERS192.168.X.X 255.255.255.0Destination Management Subnet : 10.10.X.X/24Object-Group network MGMT_VLAN10.10.x.x 255.255.255.0i am using object ...
Redistributing default route from BGP to OSPF in two different VRFs
Hello everyone,I created this lab in GNS3 and I was playing around before an activity I have to complete:As you can see, I have a situation in which two of my routers are forming an eBGP neighborship with a single provider. The exit point to the Inte...
MPLS LDP Transport Address on Parallel Links
Hello, everyone.My book states the following regarding multiple links between routers:When a router has multiple links toward another LDP router, the same transport address must be advertised on all the parallel links that use the same label space.My...
DUO initial setup
Hello,i need to know the initial setup steps for Cisco DUO tenant.should i receive email with the license. it's first time for me to create a tenant.
Can no longer Import Base64 PKCS12 in ASA9.16 Code
I have been installing certificates on my ASA's using Base64 PKCS12 files since 9.1 code using command line. Never a problem. Upon upgrading to 9.16 code, I can no longer enter my Base64 file via command line. It works in ASDM. I read and re-read...
Resolved! Cisco air-ap1815i-e-k9 no save config
Hi,I'm not a SW engineer, but my neighbor brought me a Cisco air-ap1815i-e-k9 AP to configure for him.I connected the device to a PoE switch and it started blinking green.My main router/firewall is pfSense, so I found the device's IP address in DHCP ...
Resolved! Re: WLC9800 freezing issue
I am facing the same issue with 9800 running on the 17.12.6a version , we just lose connection to the core switch even though the link is showing up on both sides , bouncing the interface does not help.Did anyone find a solution for this
CISCO Identity Services Engine (ISE) Device Profile and OUI data
Over the last couple of months I noticed that the ISE OUI database has exactly one (1) OUI update per 7 days.I'm subscribed to the feed-admin mailinglist and receive one mail per week.When compared to an online OUI database, I see 1100+ changes over ...
Cisco Remote Access VPN not working when showing connected
Hi,We are experiencing the issue where even though Cisco Secure Client connects to our Remote VPN successfully it stops working either straight away or after a while. When it stops working it still shows as connected in secure client but all access t...
Meraki Documentation Digest July 17th - July 23th
New articlesSubscription - Licensing FAQsCo-Termination Licensing FAQsPer-Device Licensing (PDL) FAQsChange: New articles. MG AccessoriesMX AccessoriesMS AccessoriesCatalyst AccessoriesMR AccessoriesMV AccessoriesMT AccessoriesChange: New articles. M...
Resolved! Deployment of Cisco ISE using Azure Local
Hello, has anyone had experience deploying an ISE VM from Azure Marketplace to an on-premise Azure Local deployment? I can't find the process documented anywhere but as Azure Local sits on top of Hyper-V I would like to think it would work.
Shun configured but not working
have had scanning threat enabled for years. New assistant typed "no shun" instead of "clear shun" and now the "show shun" doesn't show anything. Usually have about 100 in a matter of minutes. Have turned on and off via GUI and verified the config ...
Effective Bandwidth Policing on cisco ASR1001
Dear All.,I need assistance on placing a restriction on a client Bandwidth usage.I have applied the following config without any result:class-map match-all FBN-CLASSmatch access-group name FBNmatch dscp cs6match vlan 2186policy-map FBN-POLICYclass FB...
CISCO 93500 32C
CISCO C9500 32C has no uplink ports, so is the case like it cannot be used in access or Distribution layer? Also, Is it necessary that Uplink ports must be always SFP ports? ( Since we have to use fibre optic cable for uplinking)
| User | Helpful Count |
|---|---|
| 75 | |
| 70 | |
| 53 | |
| 47 | |
| 46 |
