Activity in Technology and Support
ISE Profiling Conflict
Hi all,I’m relatively new to Cisco ISE, and I’m running into a profiling challenge I could use some help with.We have an existing deployment of Device A that authenticates via MAB and is correctly profiled using a custom policy. I’ve now been tasked ...
VLAN issues
I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
Resolved! CISCO 9200 "No space left on device"
Hello,I am trying to update a cisco 9200 switch ( in fact, it's a stack, there a 2 switchs).Switch Ports Model SW Version SW Image Mode------ ----- ----- ---------- ---------- ----* 1 32 C9200-24P 17.06.05 CAT9K_LITE_IOSXE INSTALL2 32 C9200-24P 17.06...
Multi Phase 2 connections with IPSec Site 2 Site
ive got a problem i cant seem to figure out. When my Ipsec tunnel is built it makes a new phase 2 connection every 60 seconds. 1.1.1.1 = Cisco Router2.2.2.2 PfSense Router----- Connection configuration -----1.1.1.1 => Internet <= 2.2.2.2-------------...
Change Webauth Consent page to HTTP
We have two Cisco Catalyst 9800-L-F WLC's in HA config.We setup a Guest wireless SSID with a custom WebConsent page.Currently when a use accesses the SSID it takes them to a "Your connection is not private" HTTPS page.We don't need HTTPS on our Gues...
Artificial Intelligence Features in Catalyst Center
In the following webinar you will learn to start Utilizing AI in your operational network, Leverage AI capability to understand trends and insight. By the conclusion of the webinar, you should be able to Enable proactive issue resolution by knowing b...
NSO Upgrade Planning Best Practices
In this session, we will explore the upgrade best practices for Cisco NSO in detail. We will cover critical steps such as pre-upgrade planning, system health checks, backup and rollback strategies, staging and testing in a non-production environment,...
How to extract OID from SNMP messages for IOS devices
How to extract the OID from a SNMP message for IOS/XOS I need to monitor the temperature of the Router therefore please provides us the process to be followed up Nisheeth
vManage Install Root CA got Error org is missing
Hello, has anyone encountered this problem? I installed Root CA on vManage 20.9.5.2 and tested it by creating it from vManage, openssl and xca and got the same error. openssl req -x509 -new -nodes -key ROOTCA.key -sha256 -days 730 \> -subj "/C=US/S...
Cisco WSA Proxy commands For Integrity Monitoring and its important
Dear Community,I hope you are doing well.I would appreciate your support in resolving the following query:What are the recommended commands for Cisco WSA Proxy related to Integrity Monitoring, and what is the significance or purpose of each command?Y...
CSCwi60509 - Excess fans shown in APIC GUI
APIC reports excess 14 fans failed.i.e excluding the 14 fans that really exist. APIC 1-14 fans will show ok but unreal 15-28 fans as failed. How do I get rid of the messages or stop them?
DUO settings export
Has anyone created a script that can collect ALL the settings for an account (user and admin) into a file that can be used to duplicate the account settings for a new account? And is there a script that can use that output to copy those settings into...
Entra External Authentication Method errors: AADSTS900144
Hi all,Has anyone else noticed in the last couple of days if EAM (External Authentication Method) is configured for MFA with DUO in Entra and some end users are getting:AADSTS900144: The request body must contain the following parameter: 'externalAut...
patch ISE server from 3.3 patch-4 to patch-6 via CLI
I do not have a test environment to test so I am asking here. I have a five nodes cluster environment 3.3 patch-4 and I need to get them to patch-6, in a safe way. My environment:node1: Primary Admin, Secondary MnTnode2: Secondary Admin, Primary ...
"Content is not allowed in prolog" via /admin/API/mnt/Session/UserName
Hello, I am following these docs: https://developer.cisco.com/docs/identity-services-engine/latest/using-api-calls-for-session-management/#detailed-session-attribute-api-callsUsing this CURL request:curl -X POST -k -H 'Accept: application/xml' -H 'Co...
| User | Helpful Count |
|---|---|
| 93 | |
| 87 | |
| 81 | |
| 72 | |
| 69 |
