Activity in Technology and Support
IE-3300 Series CAD Models
We are attempting to use your range of IE-3300 switches to satisfy a specification requirement for an upcoming project. Are there any CAD models available?I'm looking for DWG or STEP files available that depict the IE-3300 series so that we can add t...
Strange Issue on c9200L stack
Dear ALL, We are using the 2 x C9200L-24T-4X(17.12.05) as stackble L3 core switch(Hold all subnet gateway) and has 4 x C2960 switch as access layer switch(using ether-channel connece to c9200L), the spanning-tree mode is rapid-pvst. We found our ne...
How do I configure ASA firewall rules?
Hi All,I'm Kamal Hinduja, based in Geneva, Switzerland (Swiss) . Can anyone explain How do configure ASA firewall rules? Thanks, RegardsKamal Hinduja Geneva, Switzerland
SSL VPN Certificate Authentication
I'm looking for a way to send the non-exportable certificate request from clients using different OS ( Windows, Linux and Mac). Then check them on CA server. After approval, the non-exportable certificate become available to client to install. Then I...
Cisco CP-6821
Hi, Can i configure the Cisco CP-6821-3PCC-K9= to work as Hotline in Point to Point Mode, without using the UCM or third part call manager. The installation is being used for a critical facility and application is only to use the phones as Hotline....
Disabling trunk interfaces
Hello!There is such a problem in the network. There is a C9500-40X core, it is responsible only for the user segment of the LAN (desktop PC, IP phones, printers, air conditioners, UPS, video cameras, etc.). Eleven floors are connected to it via MM fi...
Configuring Cisco ASA for MCI
I have a question on configuring Cisco ASA with multiple certs. I am new to configuring MCI to cisco ASAFor the identity Certificate on the same appliance, we generated CSR and generated the pkcs12 certificate outside the ASA appliance.My question is...
EEM applet variables and regex
Hi,Im fiddeling with various EEM applets and feel a bit held back by the lack of documentation. Or maybe my google-searching skills have declined. First: Is there an official documentation of variables somewhere? So far I have pretty much brute-force...
Cisco ISE Deployment in Azure - Nightmare experience!
Hi,Has anyone been able to successfully deploy ISE in Azure using expressroute from on-premise to the cloud.We have had ISE running in Azure for about 3-4 months now and have noticed a large amount of fragmentation using EAP-TLS. The Cisco guide sugg...
CX Cloud Agent
Hi, I need to migrate this prodcut to aws, is there any limitation to run cx agent on a bare metal on AWS with hyper-v?as cx agent only supports local vm configuration only(vmware and hyper v) Im think of using a bare metal to install hyper-v while c...
C9000v doesnt recieve traffic
hey im using the qcow2 image both in virt-manager and GNS3, and its like it doesnt see the packets. i capture on wireshark the arp reply's but if i do show arp its incomplete. very strange!! tried to switch from virtio to e1000 interfaces - but they ...
Resolved! Blade B200 M3 "Compute Failure" after CPU upgrade to V2
We got a defective UCS blade B200 M3 equipped with E5-26xx V2 processors. We also have a replacement blade server but with V1 processors. So we took the good V2 processors from the defective blade and put them into the replacement server...Now comes ...
cbs 220 Dynamic MAC address table full (32768 entries)
Hello i am using a cbs350 core switch and 2 cbs220 switches for other devices like workstations. The cbs 220's are producing a lot of Dynamic MAC address table full (32768 entries) messages while the mac address-table is nearly empty.CBS220-48T-R211#...
OSPF stuck in exchange / Vlan Trunk
Hello,I have two routers connected with multiple switchs beetween.I'm encountering a problem for forming adjencies in OSPF.I don't understand something, all my interfaces are with 1500 mtu value. But when i put a link beetween two switchs in trunk mo...
Upgrade firmware Cisco Access Point 6300H
Hi all,I have an access point Cisco 6300H but Mobility Express firmware.How i can upgrade it to Lightweight version through USB port?Thank all.
| User | Helpful Count |
|---|---|
| 112 | |
| 88 | |
| 74 | |
| 62 | |
| 61 |
