Activity in Technology and Support
Receiving Untrusted Server Certificate
regarding network addresses certificate is expired, what should i do, should i keep going ?
FMC Health Monitor Shows "Process Health – No Data Available"
We are facing an issue with FMC Health Monitor for a Cisco Firepower 4140 FTD.Environment:FMC: Cisco FMC 4600 (v7.2.9)FTD: Cisco Firepower 4140FTD Software: 7.2.5Snort: 3.1.21.500-21Snort 3 is currently runningFMC-managed FTD HA pairDetection Engine ...
Cisco FMC-4600 HA Sync Failed
We have two Cisco FMC-4600v7.2.9 (build 44) running in HA is two separate geographical sites. Both were in HA and running perfectly. HA failover also working perfectly. But now it's showing HA Sync Failed. Please find the screenshots shown below.Plea...
IE-9320-26S2C-E - Power Supply - How many provided with Base Model?
Documentation says: "The Cisco Catalyst IE-9320-26S2C-E switch supports dual power supplies that are field-replaceable and redundant. However, it requires only one power supply for system operation, and the second power supply is optional for redunda...
Kickstart Your Network: Cisco Catalyst Center Expert Insights Series
Join our Expert Insights Series, "Kickstart your network: Cisco Catalyst Center essentials," designed to help you build a robust foundation for your network management. This series provides the guidance you need to deploy with confidence, implement c...
Resolved! 9800-40 map calendar profile to specific APs
I have a 9800-40 that has APs at our local office as well as remote offices. Same guest wireless SSID. Remote office wants guest wireless disabled after hours, but local office needs it on. I created a calendar profile, but if I map it to my guest...
Recommended Number of NAT Entries for the Cisco 891FJ
I am configuring static NAT on a Cisco 891FJ router.What is the recommended number of NAT entries? (For example, around 100 to 300.)
SDA Wireless Client Roaming
Hello,I am trying to clarify a little doubt. Considering that I am using SDA with LISP Pub/Sub Model, when a client roams (either Wired or Wireless), is the CP going to publish the L2 and L3 Client address+ new RLOC entries to all subscribed nodes (t...
LUA script to change username extracted from certificate
Hi guys,I need help in write simple script that will be used during SSLVPN connection.I have issued certificate in my AD with UPN like [email protected] and need to rewrite this to something like j.smith.Probably using REGEX or something like t...
Yealink Phone Firmware Updates over SD-WAN via Microsoft Teams
I'm having an issue where the firmware updates for my Yealink MP52-E2 and MP58-E2 phones are failing over Meraki SD-WAN. Has anyone come across this issue and been able to resolve it?
Catalyst 9000 Always-On Sandbox — SSH Authentication Failing with Vali
Hello,I am experiencing SSH authentication failures on the Catalyst 9000Always-On Sandbox despite using the correct credentials from the I/O tab.Environment:- Sandbox: Catalyst 9000 Always-On- Host: devnetsandboxiosxec9k.cisco.com- Username: "my-user...
MAC address of AP C9115ax needed before installation
Hi Cisco Community,is there a chance to get the Ethernet MAC address of a e.g. Cisco C9115AX devices from a Cisco portal?I like to add the information to our device documentation without scanning the box.Thanks for your feedback.
AP not joining WLC 2504
in my home LAB, i have a WLC 2504 running 8.5.102 and i have 2 air-ap2802i-e-k9 access pointsthey are in the same LAN, can ping each other and infact establish connection but terminate immediately.and i think the problem is with the licenses being ma...
Resolved! Wireless Controller 9800 RP port
Hello,I am trying to set up SSO but I struggle to activate RP ports. I have connected them via fiber to swiches in the same vlan and I do not get any link. I do not see that RP port as available port in Web Gui menu redundancy config. I have attached...
Resolved! Re: Wireless Controller 9800 RP port
Hey all,Just wanted to confirm that this also works with the new Cisco WLC 9800H RP using a 1G GLC-SX-MMD SFPAfter spending long time on tshoot, I found that the RP port would not work with a 10G-SR SFP, Once I replaced it with the 1G GLC-SX-MMD, the...
| User | Helpful Count |
|---|---|
| 87 | |
| 51 | |
| 41 | |
| 38 | |
| 36 |
