Activity in Technology and Support
Sticky ECMP misusage or software bug?
We are trying to achieve the goal of persistent load-balancing with ASR9000. The network is a Data Center based on Kubernetes, where the ASR9000 works as DC gateway for all worker nodes. However, after the link fails toward one worker, the routing ta...
dial-peer voice, prefix 9 - VG320 CLI
I would like to use the "Prefix" command in a dial-peer on my VG320I'm using the configuration below, but the Prefix 9 doesn't seem to be working.If I dial a 4-digit extension from this port, the call goes right through.I would have thought I didn't ...
Re: Sticky ECMP misusage or software bug?
Hello everyoneI’d like to clarify whether Sticky ECMP is supported and working on the NCS55A1 running IOS XR 25.2.2.Also, is it true that there is a limitation preventing this feature from working within a VRF? If so, where can I find the official do...
XR:NCS5500/ASR9000 Persistent Loadbalancing or "Sticky ECMP"
This document applies to NCS5500 and ASR9000 routers and has been verified as such. Introduction traditional ECMP or equal cost multipath loadbalances traffic over a number of available paths towards a destination. When one path fails, the traffic g...
Cisco PCCE 15.0 Upgrade
We are running the PCCE 2K model with Windows & SQL 2019. We are now planning to upgrade only Cisco Applications to 15.0, without an OS/SQL change.The customer wants to change the OS/SQL after a few months. According to the Cisco document, this appro...
A New Chapter for DevNet Sandbox
Hi @All We have some news to share. Please read the message below:Beginning August 1st, the current Sandbox platform will temporarily transition offline as we build something entirely new from the ground up, a platform designed to deliver a more focu...
Environment is stuck
The following environment is stuck in launching. Can the sandbox team please stop it?Firepower Threat Defense REST API-20260527T11052152Thanks in advance
Users are unable to connect to Hotel WIFI/DELTA WIFI with Always on VPN setting
In our company we have employees that travel and currently in our users XML profile(Cisco Secure Client) we have everyone configured with the "Always on VPN" set. This affect all our users trying to connect to Hotel WIFI's and Airline WIFI access. ...
ENTRA ID Registered Devices
We are currently running fully on Microsoft Entra ID, and things are looking pretty solid so far.--> All our Entra‑joined (or enrolled) devices are authenticating using EAP‑TLS (device-based)--> We’re leveraging device group membership in Entra ID to...
Command "netconf-yang" doesn't open port 830
Greetings,I am using a Cisco ISR4321 running IOSXE 16.06.04 I am trying to get started with NETCONF and according to every tutorial I've read the command "netconf-yang" should be enough to start the NETCONF service and open Port 830, however, trying ...
ADE Enrollment Fails "Unable to Download Configuration" (HTTP 403)
Hi everyone, fis anyone currently experiencing the same issue with iPad Air 2 devices in Cisco Meraki Systems Manager?Whenever I try to set up an iPad Air 2, the following error appears in Setup Assistant: "Configuration download failed" / "Unable to...
Cisco Room Bar in MTR Mode: Starting Webex Wireless Share Disconnects
Has anyone else seen this behavior with Cisco Room Bars running Microsoft Teams Rooms (MTR) mode?We have Cisco Room Bars with Room Navigators configured as MTR devices. The room joins Teams meetings normally using the Join button on the Room Navigato...
Can I register SIP device on CUBE and passthrough to existing trunk
I have the CUBE (ISR4321) connected to a hosted SBC via a SIP trunk. I use this to route calls between the on-prem CUCM and Teams. Can I register an on-prem SIP device, such as an intercom or ip speaker to the CUBE and allow the traffic to continue o...
ISE cli admin removed after upgrade to 3.4?
I'm in the middle of configuring a new set of ISE servers, and I found that after i upgraded from 3.3 (wich the hardware came with) to 3.4 i could not log into cli any longer. GUI was working fine. So i do the admin password recovery and it tells me:...
Webex desk pro screen does not turn on
Hi, my Webex screen does not turn on.it was working, then I wanted to do a reboot. I used the button to shut it off. After that I used the button to turn it on. I see the screen going from totally black to dark grey. The led is blinking. After a whil...
| User | Helpful Count |
|---|---|
| 66 | |
| 58 | |
| 49 | |
| 45 | |
| 44 |
