Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
I am looking to find out how long Cisco Spaces keep client location data in storage, is it only 30 days worth of data or can we keep the data for 2 to 3 years.
Security appliances software versions MX 26.2.2 changelog Executive summaryMX 26.2.2 is the second beta release for the MX 26.2 release family.This release adds custom intrusion policies, WAN Uplink Sharing, and organization-wide port profiles.It als...
I am looking for steps to backup Expressway C&E through CLI and its commands. I knew it can be done via GUI but i am looking for some automation opportunities by passing CLI commands to EXP C&E and take backup and store those files.
Hey everyone.Really looking to see if anyone has experienced anything similar here. We updated our FTD 1140s to 7.6.4 about 2 months ago and have started seeing High Data Plane memory usage. Recently this has began to cause these Firewalls to crash a...
I have an N9K-C93600CD-GX that will be used to replace our existing C9504 Spine. From my understanding, the new switch needs to be connected to the fabric using ports 29-36 for discovery.I have connected the N9K-C93600CD-GX to the fabric through port...
We have one Auth Proxy set up that points to one domain controller and also is set up for SSO. I want to set up another Auth Proxy. Can I have it point to another DC for the same domain (we just have one AD domain)or does it have to be the same one ...
Hi everyone,I experienced an issue yesterday with a Cisco C9350-48T stack running IOS XE version 17.18.03a.The stack consists of 7 members. During the initial installation, I was unable to fully close the stack ring because the available stacking cab...
Hello Ladies and Gents,I have a need to create 3 separate Mesh groups for number of AP, one group AP, must not join another group AP.Each group will have a dedicated root AP, supposedly only the root AP will have wired connection to the corporate net...
Hi, I found that we dont have call policy config enabled in our Expr -E and -C. Right now we are getting spam calls and i see they can be blocked by enablig Call policy and creating rules to block spammer URI . My concern is since i dont have any ru...
We had a link connected to a Nexus 9K and port configurations as follows.--interface Ethernet1/11switchport mode dot1q-tunnelswitchport access vlan 822spanning-tree port type edgespanning-tree bpdufilter enablespeed 1000no negotiate auto-- Then, we m...
1- C1300-48FP-4X Catalyst 1300 - 38876627+48-Port GE, Full POE, 4X10G SFP2- C1300-24FP-4X Cisco C1300 - 30798414Switch, 24x PoE+ 370W/4x 10G SFP+/Rackmountable May i know if this switches are out of support ?
We have a number of URLs included on internet breakouts in our MX devices. The ones which are mostly ASW hosted services, the DNS URLs generally resolve to a CNAME and then to an IP address. The IP addresses also appears to change dynamically from ti...
Hi guys,I'm doing an installation of two buildings at a customer.1 building has a C9500 stack as core with C9200L switches as access.After battling some issues with the sticky 1-512 vlan thing and port-channel issues I was finally able to move to the...
Hello,I have Cisco 8841 model phones, which currently have SIP firmware installed. Now, I want to upgrade all of them to MPP/3PCC firmware.However, when I try to do this via Tftpd64, which used to work before, I am now unable to upgrade the firmware....
I have an AP 9176 which is not updating the regulatory domain.The AP join tag has a correct config. other same model APs on same switch are able to update the country code and regulatory. error on wlc %APMGR_TRACE_MESSAGE-5-AP_COUNTRY_CODE: Chassis 1...
