Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! 3850 WLC: Enabling Access Points via CLI
Hi, we have a couple of 2802 APs registered on a 3850 (16.3 Denali). Obviously the "Admin Status" of the APs must be set to "Enable" to put them into operation. I found it in the web gui (see attachment).Does someone know how to do it via CLI? Th...
Hi team, AP suddenly stopped working . It currently shows RED color in status LED. All other APs are working fine . We have changed POE switch port but still issue persists. We have other 31 Cisco APs which are working the same way it is working ( l...
Running Mobility Express on a 3802E. When I select 160MHz wide bandwidth on the 5GHz radio, it stays 160MHz for a while and when I go to check on it a couple hours later, I see it has reset back to 80MHz. I don't see this on the caveats list.
I'm looking to upgrade my 5508 WLC with 1552E AP's to version 8.3.102.0. I see that the update is split into two images if using 1550 Series AP's with 64 MB and 128 MB of memory. How do I figure out how much memory my 1552's have? If they have, sa...
Resolved! 3802E weaker 5GHz
The power level on 2.4GHz is 22dBm. The power level on 5GHz is 23dBm. Scanning around with a WiFi analyzer I consistently see the 5GHz signal -10 lower than the 2.4GHz. Even line of sight. Is this a defective 3802E?
Hi, I have multiple customer sites with Shareband backhaul and flexconnect AP's with Central controller. We have noticed that we lose the AP's intermittently and now need to upgrade the Controller software. One of the issues being brought up is th...
I am implementing a HA pair of 2504's. I want to verify that the vlan ID's should match on both controllers. Thanks
Resolved! Antenna Gain Configuration in WLC
Hi, What does it mean to specify in the WLC for each AP the dB of the antennas. The antenna is a passive component and it just focuses the signal, how come they give us the option to specify dBi, i don't understand the benefit and the effect. If we l...
Hi guy, I would like report an issue with the CleanAir submenu: according to the output the AP-058 report a Microwave Oven (see attached image). But the AP-058 is a old 1242 AP that don't have CleanAir: AP SummaryNumber of APs.........................
Hello we have Cisco 3850 in all branch offices acting as MC/MA along with wired clients , we need to design the multicast for wired and wireless users , I don't have any issues for my wired clients but I have never done for wireless users , can some...
How to know the Ap is down from the controller . There are no indicator in wireless controller to show the ap that is down in wireless controller 5760. Please help
We need to change the SSID of some of our WLAN's. On the most recent WLC versions, we're able to do this from the WLC GUI, but this seems to make the PI database out of sync. So... Can we change the SSID directly from PI and push it to the WLC's? Or...
[Diagram]Router --- Router ----Cisco Bridge ))) ((( Cisco Bridge --- Router---- Router [Question]. Is it possibe to pass the route traffic ?
Resolved! Management vlan not working well
I install one cisco AP 1832i version 8.3.102.0 for one customer .I have WLANs problem.There are 2 ssid in WLANS,one for employee and one for guest.employee is under Management vlan (netwrok-192.168.0.0)and guest is under vlan 20(network192.168.20....
Hi there, After a power outage the message bellow appears on my APs. Looks like the certificate has expired. I’ve verified the date & time on my WLC.Do I need to upgrade the ios? It's currectly runinng 12.4(18a)JA1. Are there any workarounds? *Jan 18...
